Pacific hydrostar 65078 Скачать руководство пользователя страница 7

Page 7

For technical questions, please call 1-800-444-3353.

SKU 65078 

        

allow the engine to completely 

b. 

cool.
then, remove the spark plug 

c. 

wire(s) from the spark plug(s).

Keep all safety guards in place and 

2. 

in proper working order.  Safety 

guards include muffler, air cleaner, 

mechanical guards, and heat shields, 

among other guards.

do not alter or adjust any part of 

3. 

the equipment or its engine that 

is sealed by the manufacturer 

or distributor.  Only a qualified 

service technician may adjust 

parts that may increase or 

decrease governed engine speed.

Wear ANSI-approved safety goggles, 

4. 

heavy-duty work gloves, and dust 

mask/respirator during use and 

service.
Keep the high pressure hose 

5. 

connected to the pressure washer 

and spray Gun while the system 

is pressurized.  Disconnecting the 

pressure hose while the unit is 

pressurized is dangerous, and may 

cause injury.
Do not allow the high pressure hose 

6. 

to come in contact with any hot 

part of the unit.  The hose might be 

damaged, possibly causing it to burst 

or leak under high pressure. 
Maintain labels and nameplates 

7. 

on the equipment.  These carry 

important information.  If unreadable 

or missing, contact Harbor Freight 

Tools for a replacement.
If water is leaking out of the Pressure 

8. 

Washer immediately turn off the 

unit.  Unplug the Pressure Washer, 

and discharge all pressure before 

tightening fittings or having repair 

work done by a qualified technician.

When the engine is running, do not 

9. 

allow the Pressure Washer to remain 

idle for more than two minutes.  If 

allowed to remain idle, the water in 

the unit will heat up, possibly causing 

damage to the Pressure Washer.  
Have the equipment serviced by a 

10. 

qualified repair person using only 

identical replacement parts.  This 

will ensure that the safety of the 

equipment is maintained.  Do not 

attempt any service or maintenance 

procedures not explained in this 

manual or any procedures that you 

are uncertain about your ability to 

perform safely or correctly.
Store equipment out of the reach of 

11. 

children.
Follow scheduled engine and 

12. 

equipment maintenance.

refueling:

Do not smoke, or allow sparks, 

1. 

flames, or other sources of ignition 

around the equipment, especially 

when refuelling.

Do not refill the fuel tank while the 

2. 

engine is running or hot.

Do not fill fuel tank to the top.  Leave 

3. 

a little room for the fuel to expand as 

needed.
Refuel in a well-ventilated area only.

4. 

 save tHese 

instructiOns.

Содержание 65078






































Отзывы: