background image

Radio Replacement and 

Steering Wheel Control Interface 

for Toyota / Lexus / Scion Vehicles

RP4.2-TY11

RadioPRO App

Use of the RadioPRO App allows 

you to do the following:

Configure User Interface Options such

as:

Factory amplifier settings (Bass,

Mid, Treble, Gain, Fader and

Balance)

Real Time Fading

Update Product Firmware

Read Firmware/Hardware Versions

Access Product User Manuals

PLEASE NOTE: 

The interface must be connected to the vehicle when using the following features of the Radio PRO App:

Factory Amplifier Settings

The interface does not need to be connected to the vehicle when using the following features of the Radio PRO App:

• Firmware Updates

Reading firmware/hardware versions

Infotainment/Factory Amplifier Settings

The RadioPRO app will also allow you to adjust the settings of the factory amplifier. You can adjust Amp Gain, Fader, Balance, 

Bass, Mid and Treble and real time fade. When real time fade is enabled in amplified systems, it will allow fading to be 

controlled directly from the aftermarket radio. Restoring factory settings on the module will default all values back to middle.

Содержание RadioPRO4 RP4.2-TY11

























Отзывы: