background image

Fitting the Cartridge Filter - Vacuuming Dry Matter

The cartridge filter should come pre-assembled onto the vacuum unit. 

However it is still a good idea to check that it has not come loose 

during transport and is still properly fitted before use.

For dry vacuum cleaning always 

use the cartridge filter. Mount 

the filter so that no air is sucked 

through the filter cage without 

first being filtered.

1.  Press the flat end of the 

cartridge filter onto the filter 

cage until it is stopped by the 

step in the lid part.

2.  Place the filter lid on the 

bottom of the filter and turn 

the handle clockwise to lock it 

into place.

3.  To remove the filter, turn the filter lid handle anti-clockwise to 

release it. Remove both the filter lid and cartridge filter.

NOTE:

 Do not use the foam filter when vacuuming dry matter. 

Fitting the Foam Filter - Vacuuming Liquid

For wet-vacuuming, slip the 

supplied foam filter over the filter 

cage.

NOTE:

 Do not use the cartridge 

filter when vacuuming liquid.

WARNING! 

SWITCH OFF THE EQUIPMENT IF LIQUID 

OR FOAM IS EMITTED WITH THE EXHAUST AIR 

WHEN WET VACUUM CLEANING.

WARNING! 

THE WET & DRY VACUUM IS NOT 

SUITABLE FOR THE VACUUMING OF COMBUSTIBLE 

LIQUIDS.

WARNING! 

WHEN WET VACUUMING, THE 

SAFETY FLOAT STOPS THE VACUUM SUCTION 

AUTOMATICALLY WHEN THE MAXIMUM CAPACITY 

IS REACHED. TURN OFF THE VACUUM & EMPTY 

THE TANK BEFORE CONTINUING TO VACUUM.

Draining Liquids From The Tank

Spills and puddles can be vacuumed directly into the tank with the 

foam filter fitted for easy clean up and disposal.

Note:

 When vacuuming large quantities of liquid, do not immerse the 

nozzle completely into the liquid, leave a gap at the nozzle/tool to 

allow air inflow.

1.  Hold the vacuum over a laundry sink or household drain.

Note: 

Only dispose of liquid waste into household sinks & drains 

if safe to do so. Improper disposal of hazardous waste can cause 

pollution and harm.

2.  Turn the drain outlet cap 

anti-clockwise to loosen and 

remove it.

3.  Allow any collected liquid 

in the tank to flow out. 

Tip the vacuum slightly 

to allow any liquid at the 

bottom of the tank to flow 

out too.

4.  Rinse out the tank if 

necessary and replace the 

drain outlet cap.

2. FILTER SELECTION

3. WASTE DISPOSAL

a.

b.

c.

WARNING! 

NEVER USE THE WET & DRY VACUUM 

CLEANER WITHOUT A FILTER. ALWAYS ENSURE 

THAT THE FILTERS ARE PERFECTLY SECURE.

Содержание WDVB-1312









Отзывы: