Ozito PMT-004 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 40

background image

a. Press

b.

a. Press

b.

Carrier Plate

Cover

Carrier Plate

31

7. Thread the two ends of the line through the metal

eyelets in the line spool housing.

8. Align the spool cover, at the tab in order to press down

and turn the spool cover into the line spool housing to

reassemble the two halves.

9. Pull the two line ends sharply to release them from the

line holders in the line spool.

10. Cut the excess line to a length of around 130mm. This will reduce the load

on the engine when starting and warming up.

11. Refit the line spool.

Sharpening Safety Guard Knife Edge Blade

The safety guard knife edge blade can
become blunt over time. When you notice
this, undo the screw holding the blade on
the guard hood. Clamp the blade in a vise.
Sharpen the blade with a flat file and make
sure that the angle of the cutting edge is not
altered in the process. File in one direction
only.

Safety Guard

Remove all grass and weed remains at regular intervals to prevent the shaft
tube overheating. Grass and weed remains become trapped under the safety
guard, and they prevent the shaft tube receiving adequate ventilation.

«
...
29
30
31
32
33
...
»

Содержание PMT-004









































Отзывы:

Нет отзывов

Похожие инструкции для PMT-004

Бренд: Gates Страницы: 36

Бренд: Nederman Страницы: 120

Бренд: Altronix Страницы: 2

Бренд: Delta Страницы: 15

Бренд: Ryobi Страницы: 24

Бренд: Maestri Страницы: 16

PRO 8425 0206 30

Бренд: Atlas Copco Страницы: 64

Бренд: THERMOBILE Страницы: 66

Бренд: Protool Страницы: 60

Бренд: OfiTE Страницы: 4

Бренд: Parkside Страницы: 53

Бренд: Stanley Страницы: 233

Бренд: Yost Vises Страницы: 5

Бренд: M-system Страницы: 4

Бренд: SW-Stahl Страницы: 17

2000-2 LNB Series

Бренд: Cross Technologies Страницы: 8

Бренд: Kaindl Страницы: 9

Бренд: Clearaudio Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды