Ozito PMT-004 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 40

background image

Carrier Plate

Cover

Carrier Plate

Blade

Pressure Plate

Pressure Plate

Cover

Nut

Carrier Plate

Cover

Carrier Plate

Blade

Pressure Plate

Pressure Plate

Cover

Nut

13

Fitting the Brush Cutter Blade

3. BRUSH CUTTER BLADE

1. Fit the Carrier Plate over the spindle. Place

the Brush Cutter Blade onto the Carrier
Plate, ensuring that the hole in the blade
is correctly seated. Also ensure that the
direction of rotation arrows on the blade
match the arrow on the blade guard.

2. Place the Pressure Plate on the spindle,

followed by the Pressure Plate cover and
loosely fit the nut, turning

counter-clockwise

(the nut has a left-hand thread).

3. Before tightening the nut, align the hole

in the Carrier Plate with the hole in the
Carrier Plate Cover and insert the 4mm hex
key. While holding the hex key in place,
Tighten the nut, turning

counter-clockwise

.

Remove the hex key.

WARNING!

THE BRUSH CUTTER BLADE HAS SHARP EDGES. FOR YOUR

SAFETY, PLEASE USE GLOVES.

WARNING!

DO NOT OPERATE THE BRUSH CUTTER ATTACHMENT

WITHOUT THE SAFETY GUARD FITTED.

WARNING!

THE BLADE NUT MUST NOT BE RE-USED. WHEN

RE-INSTALLING THE BLADE, USE A NEW BLADE NUT. FAILURE TO

FOLLOW THIS PROCEDURE CAN RESULT IN SERIOUS INJURY.

«
...
11
12
13
14
15
...
»

Содержание PMT-004









































Отзывы:

Нет отзывов

Похожие инструкции для PMT-004

Бренд: Gallagher Страницы: 104

Бренд: SAMCHULLY Страницы: 24

Бренд: Jet Страницы: 12

Бренд: ZALMAN Страницы: 7

Бренд: Bench Dog Tools Страницы: 12

Бренд: Ferm Страницы: 96

Бренд: Greencut Страницы: 20

Бренд: Stanley Страницы: 128

Бренд: Campbell Hausfeld Страницы: 16

Бренд: Promaker Страницы: 24

XTRIC 363000 80S

Бренд: GARANT Страницы: 116

Бренд: Hakko Electronics Страницы: 8

Бренд: Corsair Страницы: 42

Бренд: YATO Страницы: 104

Бренд: Yaesu Страницы: 2

Бренд: Horizont Страницы: 27

Бренд: MESTA Страницы: 26

Бренд: probst Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды