Overland Storage LoaderXpress Скачать руководство пользователя страница 94

Страница: 94 / 104

5-16

Troubleshooting

AULT

YMPTOM

ODES

(FSC)

6045

Command Overlap
Enter to Reboot or Power
Down to Clear

HARD fault - Command Overlap.

C, D, G

6046

No Pkts to Send
Enter to Reboot or Power
Down to Clear

HARD fault - No Pkts to Send.

C, D, G

6047

Invalid Direction
Enter to Reboot or Power
Down to Clear

HARD fault - Invalid Direction.

C, D, G

6048

Master Pkt ID Bad
Enter to Reboot or Power
Down to Clear

HARD fault - Master Pkt ID Bad.

C, D, G

6049

HDR CRC Error
Enter to Reboot or
Power Down to Clear

HARD fault - HDR CRC Error.

C, D, G

604A

Data CRC Error
Enter to Reboot or Power
Down to Clear

HARD fault - Data CRC Error.

C, D, G

604B

Packet Length Error
Enter to Reboot or Power
Down to Clear

HARD fault - Packet Length Error.

C, D, G

604C

Slave Address Error
Enter to Reboot or
Power Down to Clear

HARD fault - Slave Address Error.

C, D, G

8001

Bad Cartridge
Press Enter to Clear

SOFT fault - the drive was unable to seat the cartridge
on the chuck after multiple retries. This may be due to
a defective cartridge.

8002

Drive preventing
Press Enter to Clear

SOFT fault - An eject command has been rejected by
the drive because the drive is set to prevent media
removal.

8003

Unsupported Cart
Press Enter to Clear

SOFT fault - The drive has detected an unsupported
cartridge type was loaded and has rejected it.

8004

Update failure
Enter to Reboot or
Power Down to Clear

HARD fault - LTO drive reports bad flash update.

C, D, G

8005

Bad update tape
Press Enter to Clear

SOFT fault - Drive update from tape has been aborted
due to a defective tape (bad checksum).

Table 0–1 Fault Symptom Codes

Содержание LoaderXpress









































































































Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды

Overland Storage LoaderXpress, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды