Overland Storage LoaderXpress Скачать руководство пользователя страница 91

Страница: 91 / 104

Troubleshooting

5-13

AULT

YMPTOM

ODES

(FSC)

503A

Auto Cleaning
Press Enter to Clear

Not a fault code. - The loader is auto-leaning the
drive.

5090

Slave Cmd Failure
Press Enter to Clear

SOFT fault - this slave could not execute a diagnostic
command from the remote master.

6001

Comm Port Open Error
Enter to Reboot or Power
Down to Clear

HARD fault - Comm Port Open Error.

C, D, G

6002

Comm Port Send Error
Enter to Reboot or Power
Down to Clear

HARD fault - Comm Port Send Error.

C, D, G

6003

Comm Port Recv Error
Enter to Reboot or Power
Down to Clear

HARD fault - Comm Port Recv Error.

C, D, G

6004

EnQ Without IDs
Enter to Reboot or
Power Down to Clear

HARD fault - EnQ Without IDs.

C, D, G

6005

DeQ Without IDs
Enter to Reboot or Power
Down to Clear

HARD fault - DeQ Without IDs.

C, D, G

6006

EnQ Null Pointer
Enter to Reboot or Power
Down to Clear

HARD fault - EnQ Null Pointer.

C, D, G

6007

No Free Comm Blks Enter
to Reboot or Power Down
to Clear

HARD fault - No Free Comm Blks.C, D, G

6010

Pkt Send Error
Enter to Reboot or Power
Down to Clear

HARD fault - Pkt Send Error.

C, D, G

6011

Pkt Receive Error
Enter to Reboot or Power
Down to Clear

HARD fault - Pkt Receive Error.

C, D, G

6012

Status Unexpected
Enter to Reboot or Power
Down to Clear

HARD fault - Status Unexpected.

C, D, G

6013

Invalid Com Blk Type
Enter to Reboot or Power
Down to Clear

HARD fault - Invalid Com Blk Type.

C, D, G

Table 0–1 Fault Symptom Codes

Содержание LoaderXpress









































































































Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды

Overland Storage LoaderXpress, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды