manualshive.com logo in svg

Overland Storage LoaderXpress, Руководство пользователя и инструкция по установке

Поделиться
Скачать
Overland Storage LoaderXpress Скачать руководство пользователя страница 2

All information contained in or disclosed by this document is considered proprietary by 
Overland Storage. By accepting this material the recipient agrees that this material and the 
information contained therein are held in confidence and in trust and will not be used, 
reproduced in whole or in part, nor its contents revealed to others, except to meet the pur-
pose for which it was delivered. It is understood that no right is conveyed to reproduce or 
have reproduced any item herein disclosed without express permission from Overland 
Storage.
Overland Storage provides this manual as is, without warranty of any kind, either 
expressed or implied, including, but not limited to, the implied warranties of merchant-
ability and fitness for a particular purpose. Overland Storage may make improvements or 
changes in the product(s) or programs described in this manual at any time. These changes 
will be incorporated in new editions of this publication.
Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or 
usefulness of this manual, nor for any problem that might arise from the use of the infor-
mation in this manual

.

Worldwide

Headquarters

Overland Storage, Inc.
4820 Overland Avenue
San Diego, CA 92123
Toll Free: (800) 729-8725 (Toll free US)
Tel: (858) 571-5555
Fax: (858) 571-0982

Sales

Tel: (858) 571-5555
Fax: (858) 571-3664
E-mail: [email protected]
www.overlanddata.com

Technical Support

Tel: (858) 571-5555
Fax: (858) 571-3664
E-mail: techsupport@overlandstor-
age.com

Overland Storage,

EMEA

Overland House, Ashville Way
Wokingham, Berkshire
RG41 2PL, England
Tel: +44 (0) 118-9898000
Fax: +44 (0) 118-9891897
www.overlandstorage.com

Proprietary Notice

Содержание LoaderXpress









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды