Overland Storage LoaderXpress Скачать руководство пользователя страница 42

Страница: 42 / 104

2-20

Installation

OWER

OURCE

ONNECTION

3) If the LoaderXpress is one of several units you are connecting to the host, connect

them in a daisy-chain by doing the following:

•

Connect the cable from the host, to one of the SCSI connectors of the first SCSI
device

•

Connect another cable from an unused connector of the first device to an unused
connector of the second SCSI device, and so on.

•

Attach the terminator to the last unused SCSI connector of the last device in the
chain

Figure 2–29 Single Host Configuration

Power Source Connection

The AC power cable is a standard grounding AC cable, which attaches to an IEC-
compatible connector on the rear panel. Connect the cable to the connector on the module,
and connect the other end to a reliably grounded AC outlet or rack power outlet.

To maintain product safety compliance, use a power cord with a suitable electrical rating:

Table 2–1 Power Cord Rating

Country / Area

Power Cord Rating

United States

UL Listed

Canada

CSA Certified

LXL-0073

To Host

Terminator

Содержание LoaderXpress









































































































Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды

Overland Storage LoaderXpress, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды