manualshive.com logo in svg

Oval EL 2310-0BE Series, Инструкция по эксплуатации

Поделиться
Скачать
Oval EL 2310-0BE Series Скачать руководство пользователя страница 17

E-025-2-E

Fig.24

⑩ If you click the 

 button of the tool bar or "Chart and Recording" - "Active" from the menu, chart 

display and data logging are terminated.

3.5.3 Write Protect (Write protect)

① Click "Process Variables (V)" on the menu and select "Write protect", then the following window 

(Fig. 25) will be displayed.

② To exit this procedure, click "Cancel".

Date and time Percent flow rate

Flow rate

Flow velocity

Fig.25

　  "Write protect" shows whether parameter change of the transmitter is available or not.

Mode

Detail

SW1-4 Setting

Not write protected

Enables changing and setting parameters.

OFF

Write protected

Disables changing and setting parameters.
(Confirmation of parameters is available.)

ON

  NOTE : Selecting the above mode is available by changing switches SW1-4 on the

                CPU board of the flowmeter transmitter.

⑨ The content of the log file when logging interval is set to "5 Seconds" is as shown in Fig. 24.

Содержание EL 2310-0BE Series





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды