Oval ALTImass CA004 Скачать руководство пользователя страница 84

Страница: 84 / 98

L-737-3-E

10.5.3 Insulation performance

Part of transmitter (PA0K) subject to insulation:

IS circuit terminals (separate detector board: TB0, TB) - Enclosure

Withstand voltage condition: 00VAC, leak current: 3 to mA

Due to the built-in noise eliminator between the transmitter power source terminals (TB

’

s L and N) and

output terminals (TB, TB3 and TB), and the enclosure respectively, complete insulation is not provided.

In case withstand voltage test is conducted across these parts, please conduct under the conditions

below.

Withstand voltage condition: AC00V or DC0V, leak current: 3 to mA

10.5.4 Earthing terminal

. Use GND of power source terminal block or any of external grounding terminals.

. Use wires of cross section area of mm

min. (AWG min.) for grounding.

3. Coating color of the grounding wires shall be green or stripe of green and yellow.

. Class D grounding (00 ohm or less) is recommended.

. In case external wirings are used, make sure that the grounding wire is connected with the earth

terminal cover and plain washer in the sketch below.

10.5.5 About dedicated cable (for only separate type)

. In case of separate type, a dedicated cable is used for connection between the sensor and

transmitter. Use of other cables are not allowed from the point of explosionproof.

. Make sure to array the dedicated cable between the sensor and transmitter so that any current and

voltage, which attributable to electromagnetic induction or electrostatic induction and could impair

the intrinsic safety performance of the IS circuit, is never induced.

Spring washer

Earth terminal cover

Plain washer

Cross recess pan head screw

Fig.0.

Содержание ALTImass CA004



































































































Результаты поиска

Содержание ALTImass CA004

Отзывы:

Бренды по названию

Популярные бренды

Oval ALTImass CA004, Инструкция по эксплуатации

Результаты поиска

Содержание ALTImass CA004

Отзывы:

Бренды по названию

Популярные бренды