Oval ALTImass CA004 Скачать руководство пользователя страница 13

Страница: 13 / 98

L-737-3-E

5.3.2 Influences of Vibration and Pulsations

Generally, Coriolis mass flowmeters can best make measurements with minimal pipeline vibration and

pulsations. In applications where vibration and pulsations are not negligible, take the following measures:
() Locate the meter suf

ﬁ

ciently away from the sources of vibration and pulsations.

() Provide attenuators, such as

ﬂ

exible tubes and chambers. However, if this meter itself is the very source

of transmitting vibration to these elements during its operation, a drift in zeroing may result.

To get around this problem, take necessary countermeasures by, for example, locating such elements of

vibration suf

ﬁ

ciently apart from the meter.

(3) Close shutoff valves upstream and downstream of the meter at process

ﬂ

ow shutdown. (For the sake of

preventing erratic signal generation at shutoff, be sure to prevent pressure buildup inside from exceeding

the max. allowable pressure of the meter.)

() If meters of the same kind are to be installed in the same tubing, locate them suf

ﬁ

ciently apart (at least

times the face-to-face length across the meter) and secure each meter with sturdy supports.

5.3.3 Prevention of Cavitation

Cavitation can cause a loss of meter accuracy in measurement. Maintain line pressures that will not cause

cavitation upstream and downstream of the meter for this reason. Avoid making such an arrangement as to

open the line to the atmosphere immediately downstream of the meter. Care must be exercised particularly in

handling liquids of low steam pressure.
In practice, recommended minimum back pressure (pressure on the downstream side) of the meter is calcu-

lated by the formula:

＝

＋

.3Pv

Where Pd : Downstream pressure (MPa [absolute])

P : Pressure loss across the

ﬂ

owmeter (MPa)

Pv : Steam pressure at the temperature during measurement (MPa [absolute])

5.3.4 Prevention of Excessive Flow Rate

CAUTION:

Exceeding the meter's maximum flow rate will not significantly reduce the

meter's long term durability. However, the output will be held at 110% of the
allowable full scale flow rate.

5.3.5 Keeping the Sensor Unit Completely Filled

CAUTION:

The sensor must be filled with the process fluid during measurement.

A partially filled sensor unit results in large errors particularly at zeroing.

5.3.6 Bypass Line

For maintenance and servicing, it is good practice to provide a bypass loop.

Fig. . Bypass Line

Flow

Direction

Valve

Bypass Line

Valve

ALTImass

Содержание ALTImass CA004



































































































Результаты поиска

Содержание ALTImass CA004

Отзывы:

Бренды по названию

Популярные бренды

Oval ALTImass CA004, Инструкция по эксплуатации

Результаты поиска

Содержание ALTImass CA004

Отзывы:

Бренды по названию

Популярные бренды