Output Solutions C-680 LabelJet Скачать руководство пользователя страница 28

Страница: 28 / 32

•

Printer is in ink-backup mode
In ink-backup mode the printer may print more slowly
Use two print cartridges to increase print speed.

Printer doesn’t feed any paper

•

Labels are not slided in until stop.

Printer passes labels through/LEARN mode not executed

•

Wrong sensor settings on tab SPECIAL FUNCTIONS.

Resume light is flashing

•

Paper tray may be empty or there may be a paper jam.

After several print processes the printer start passing labels through
without printing

•

The manual sensor setting GAP/BLACKMARK has been changed.
execute CALIBRATE GAP/BLACK MARK SENSING mode again.

Printer executes LEARN Mode permanently.

•

Deactivate CALIBRATE GAP/BLACK MARK SENSING mode on tab
SPECIAL FUNCTIONS.

LEARN MODE mode does not detects gaps between labels

•

Move the GAP/BLACKMARK sensor slightly.

If you continue to have problems

If you continue to have problems after investigating the troubleshooting
topics, shut down, then restart your computer.

If you still have problems after restarting your computer please go to
contact hotline at

[email protected]

or contact the

Output

Solutions

custumer s49 21 74- 78 32-0

Содержание C-680 LabelJet

































Результаты поиска

Содержание C-680 LabelJet

Отзывы:

Похожие инструкции для C-680 LabelJet

Бренды по названию

Популярные бренды

Output Solutions C-680 LabelJet, Руководство пользователя

Результаты поиска

Содержание C-680 LabelJet

Отзывы:

Похожие инструкции для C-680 LabelJet

Бренды по названию

Популярные бренды