background image

SAFETY PRECAUTIONS 

 

 

 

Do not operate your stove if you 

smell smoke coming from it.  Turn it off, 
monitor it, and call your dealer. 

DO NOT 

UNPLUG IT

 

 

 

Keep foreign objects out of the hopper. 

 

 

Never use gasoline, gasoline-type 

lantern fuel, kerosene, charcoal lighter fluid, or 
similar liquids to start or “freshen up” a fire in 
this stove. Keep all such liquids well away from 
the stove while in use. 

 

 

Do not throw this manual away. This 

manual has important operating and maintenance 
instructions that you will need at a later time. 
Always follow the instructions in this manual. 

 

 

Never block free airflow through the 

open vents of the stove. 

 

Do not place clothing or other 

flammable items on or near the stove. 

 

 

Never try to repair or replace any 

part of the stove unless instructions are given 
in this manual. All other work should be done 
by a trained technician. 

 

 

The viewing door must be closed and 

latched during operation. 

 

 

The stove will not operate during a 

power outage. If an outage does occur, check 
the stove for smoke spillage and open a 
window if any smoke spills into the room. 

 

 

Do not operate the stove if the flame 

becomes dark and sooty or if the burnpot overfills 
with pellets. Turn the stove off, inspect it, and call 
your dealer. 

 

 

Disconnect the power cord before 

performing any maintenance or repairs on the 
stove. 

NOTE:

 Turning the stove “off” does not 

disconnect all power from the stove.

 

 

Do not touch the hot surfaces of the 

heater. Educate all children of the danger of a 
high temperature stove. Young children should be 
supervised when they are in the same room as 
the stove. 

 

 

Do not unplug the stove if you 

suspect a malfunction. Turn the stove off, 
inspect it, and call your dealer. 

 

 

High ambient temperature in summer 

time may cause the heat sensors on the stove to 
activate the blowers, disconnect the stove when 
not used for extended periods.

 

 

Contact your local building officials to 

obtain a permit and information on any 
installation restrictions or inspection 
requirements in your area. Notify your 
insurance company. 

 

 

The exhaust system 

must

 be 

completely airtight and properly installed. All vent 
connector joints must be sealed and fastened in 
accordance with the pellet pipe manufacturer's 
instructions to ensure consistent performance and 
avoid smoke and ash spillage. 

 

 

This unit must be properly installed to 

prevent the possibility of a house fire. The 
instructions must be strictly adhered to. Do not 
use makeshift methods or compromise in the 
installation. 

 

 

Your stove requires maintenance and 

cleaning. Failure to maintain your stove may lead 
to smoke spillage in your home. 

 

 

Allow the stove to cool before 

carrying out any maintenance or cleaning. 
Ashes must be disposed or stored in a metal 
container with a tight lid and placed on a non 
combustible surface well away from the home 
structure. 

 

 

This stove is designed and approved for 

pelletized wood fuel only. Any other type of fuel 
burned in this heater will void the warranty. 

 

 

This stove must be connected to a 

standard 120 V., 60 Hz grounded electrical 
outlet. Do not use an adapter plug or sever the 
grounding plug. Do not route the electrical cord 
underneath, in front of, or over the stove. 

 

 

When installed in a mobile home, the 

stove must be bolted to the floor, have outside air, 
and 

NOT BE INSTALLED IN A BEDROOM

 (Per 

H.U.D. requirements). Check with local building 
officials. 

 

 

The exhaust system should be 

checked,  at least twice a year for any build up 
of soot or creosote. 

 

 

Stove Builder International Inc. 

grants no warranty, implied or stated, for the 
installation or maintenance of your stove, and 
assumes no responsibility of any 
consequential damage(s).

 

 

 

 

 

Содержание HYBRID-35





































Отзывы: