background image

20 

MODES 

 
THERMOSTATIC MODE 

 

To engage this mode, the thermostat icon 

 

must be pushed 

upon starting the stove. The heat setting is then selected using the 
“Heat Level” selector. When set in thermostatic mode, the stove will 
automatically run at the heat level selected until the set room 
temperature is reached. When that occurs, the stove will switch to 
heat setting #1 (lowest) until the thermostat calls for heat again.  The 
convection blowers will also slow down to low  speed. When the 
thermostat calls for heat again, the stove will automatically switch 
back to the selected heat level. 

 

 

N.B.:

  If the room temperature remains stable and the thermostat 

does not call for heat during at least 45 minutes, the stove will shut 
down.  When the thermostat calls for heat again, the stove will start an 
ignition cycle.  Once the ignition cycle is completed, the stove will 
increase its feed rate to match the heat level selected. 

 

 

N.B.:  It is possible to change the setting of your unit such that if the 
thermostat does not call for heat after 45 minutes, the unit will remain 
at the lowest heat setting (#1) but will not shut down (this is the PILOT 
ON mode).  The stove will remain at the lowest heat level until the 
thermostat calls for heat again.  If you prefer that your unit runs 
following that logic, you need to change the setting to PILOT ON by 
the pressing the following two buttons on the PC Board:  

 

First press 

, hold it,  and then press 

.  Hold the two 

buttons for a couple of seconds. 
 

 

Once you do that, the letters P, I, L, O, T, O, N will appear on the PC 
Board to let you know that you are in the “PILOT ON” mode.  If you 
wish to go back to the default thermostatic mode (i.e. the unit shuts 
down after 45 minutes if the thermostat does not call for heat), simply 
press the same two buttons again for a couple of seconds.  The letters 
P, I, L, O, T, A, U, T, O will appear on the PC Board to let you know 
that you are in the “PILOT AUTO” mode. 

 
 

NOTE:

 When in  thermostatic mode: 

 

 

You should not operate the manual control or play with the 
temperature setting. 

 

 

YOUR THERMOSTAT SHOULD BE INSTALLED BY AN 
AUTHORIZED DEALER OR QUALIFIED TECHNICIAN. 

 

D = MINIMUM DISTANCE 15 FEET

SHOULD BE AVOIDED

 

 

Figure 42 

Thermostat location 

 
 
 
 
 
 

Содержание HYBRID-35





































Отзывы: