Ormazabal cgm.3 system Series Скачать руководство пользователя

Страница: 78 / 88

IG-183-EN version 06; 31/03/2020

Maintenance

General instructions

cgm

.3 system: medium voltage SF

gas-insulated

cubicles up to 38 kV according to IEEE and CSA standards

7.2. Acoustic grounding prevention alarm test

To test that the

ekor

.sas acoustic alarm is working correctly,

connect the

ekor

.vpis voltage presence indicator to

110 V

/ 230 V

by means of 0.16 inches (4 mm) terminals,

which are connected to the indicator between the ground

test point and the test point for the L1 phase. The auxiliary

power supply is maintained for 5 minutes. As the handle is

moved to insert the lever in the grounding shaft in order

to carry out the operation, the alarm starts to sound and

continues to sound for at least 30 seconds. It stops when

the handle is released.

The

ekor

.sas alarm can be replaced if necessary, since it is

joined to the associated elements with two friction-fit PCB

connectors:

3-pin connector, polarized for the voltage presence

indicator.

2-pin connector for the lever microswitch.

The procedure is as follows:

Remove the driving mechanism cover.

Unscrew the

ekor

.sas unit to remove it.

Undo both connectors and replace the damaged

unit; then connect it to the lever microswitch (2-pin

connector) and the voltage indicator (polarized 3-pin

connector).

Figure 7.2. ekor

.sas

unit device

Содержание cgm.3 system Series

























































































Результаты поиска

Содержание cgm.3 system Series

Отзывы:

Похожие инструкции для cgm.3 system Series

Бренды по названию

Популярные бренды

Ormazabal cgm.3 system Series, Общее руководство по инструкции

Результаты поиска

Содержание cgm.3 system Series

Отзывы:

Похожие инструкции для cgm.3 system Series

Бренды по названию

Популярные бренды