manualshive.com logo in svg

Orientalmotor BXII Series, Руководство по эксплуатации

Поделиться
Скачать
Orientalmotor BXII Series Скачать руководство пользователя страница 45

Parameter

−45−

•

•

Display the conveyor transfer speed

To display the conveyor transfer speed on 

OPX-2A

, set the conveyor gear ratio by 

using the formula below:

 

=

Conveyor speed 

reduction ratio

1

Feed rate per motor revolution

Gear ratio of gearhead 

Pulley diameter [m] × π

=

When the calculated conveyor speed reduction ratio is used, the conveyor transfer 

speed is converted as follows.

 

=

Rotation speed of motor output shaft [r/min]

Conveyor speed reduction ratio

Conveyor transfer speed

[m/min]

Conveyor 

transfer speed

Pulley 

diameter

Example:  

The pulley diameter is 0.1 m and gear ratio (speed reduction ratio) of the gear head is 20

 

䍦

63.7

Conveyor speed reduction ratio =

Gear ratio of gearhead 

Pulley diameter [m] × π

=

20

0.1 [m] × π

From the conversion formula, the conveyor speed reduction ratio is calculated as 63.7 in this example. This means 

that the "speed reduction ratio" parameter (ID: 2085) is 637, while the "speed reduction ratio digit setting" parameter 

(ID: 2086) is 1.

When the speed reduction ratio is 63.7 and the motor rotation speed is 1300 r/min, the conveyor transfer speed is 

converted as follows:

 

䍦

20.4

1300

63.7

Conveyor transfer speed [m/min] =

"20.4" is displayed on the 

OPX-2A

.

„

„

Motor parameter

All parameters can be set in both the speed control mode and position control mode.

The parameters that can be used vary depending on the control mode.

ID Parameter name

Description

Setting range

Initial 

value

Effective 

*

1

Control mode 

*

2

Speed 

control

Position 

control

290 Position loop gain Adjusts the motor response in reaction to 

the position deviation.

1 to 100 Hz

7

A

○

 

*

3

○

291 Speed loop gain Adjusts the motor response in reaction to 

the speed deviation.

1 to 1000 Hz

200

○

292

Speed loop 

integral time 

constant

Adjusts the deviation that cannot be 

adjusted with the speed loop gain.

0 to 1000 ms

33

293 Speed filter

Adjusts the motor response.

0 to 200 ms

1

B

○

*

3

294 Moving average 

time

Sets the time constant for the moving 

average filter.

1 to 200 ms

1

2064 Speed filter 

selection

Sets the filter function to adjust the motor 

response.

0: Without speed filter 

1: Speed filter 

2: Moving average

0

C

*1•

Indicates the timing for the data to become effective. 

(A: Effective immediately, B: Effective after stopping the operation, C: Effective after turning on the power again)

*2•

○

: Possible to use.

×

: Not possible to use.

*3•

Possible to use when the "servo lock at motor standstill" parameter (ID: 2069) is set to "1: Servo lock."

Содержание BXII Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды