Orientalmotor BXII Series Скачать руководство пользователя страница 44

Страница: 44 / 52

Parameter

−44−

Operation parameter

All parameters can be set in both the speed control mode and position control mode.

The parameters that can be used vary depending on the control mode.

ID Parameter name

Description

Setting range

Initial

value

Effective

Control mode

Speed

control

Position

control

323 JOG operation

speed

Sets the operation speed for JOG operation. 0 to 4000 r/min

300

○

324 JOG acceleration/

deceleration rate

Sets the acceleration and deceleration time

for JOG operation.

0.00 to 30.000 s

0.100

2069 Servo lock at

motor standstill

Uses in the speed control mode.

If the holding force is required while the motor

stops, set to "1" to enable the servo lock.

0: Free

(disable servo lock)

1: Servo lock

2081 JOG operation

torque

Sets the maximum torque based on the rated

torque being 100% in JOG operation.

0 to 250%

100

○

2084 JOG travel

amount

Sets the travel amount for JOG operation.

The motor shaft rotates 0.72° per one step.

1 to 8,388,607 step

2085 Speed reduction

ratio

The speed reduction ratio can be set by

multiplying the value in "speed reduction ratio"

parameter by the value in "speed reduction

ratio digit setting" parameter.

If the speed reduction ratio is set, the rotation

speed that is calculated based on the actual

speed of the motor will be displayed.

100 to 9999

100

○

2086 Speed reduction

ratio digit setting

0: ×1

1: ×0.1

2: ×0.01

2087 Speed increasing

ratio

If the speed increasing ratio is set, the rotation

speed that is calculated based on the actual

speed of the motor will be displayed.

1 to 5

2289 Continuous

operation

Uses in the

-compatible mode (position

control). Sets whether to enable or disable the

continuous operation.

0: Disable

1: Enable

*1•

Indicates the timing for the data to become effective.

(A: Effective immediately, B: Effective after stopping the operation, C: Effective after turning on the power again)

*2•

○

: Possible to use.

: Not possible to use.

•

How to set the speed reduction ratio

Set the speed reduction ratio as a combination of the "speed reduction ratio" parameter (ID: 2085) and "speed

reduction ratio digit setting" parameter (ID: 2086).

The relationships of speed reduction ratio and decimal position are explained by the combinations shown below.

Actual speed

reduction ratio

"Speed reduction ratio"

parameter

"Speed reduction ratio digit setting"

parameter

1.00 to 9.99

100 to 999

10.0 to 99.9

100 to 999

10.00 to 99.99

1000 to 9999

100.0 to 999.9

1000 to 9999

•

Display after setting the speed reduction ratio

•

Speed reduction ratio

•

Speed increasing ratio

Speed reduction ratio 1.00 to 9.99

Speed reduction ratio 10.00 to 99.99

Speed reduction ratio 100.0 to 999.9

Speed reduction ratio 1000 to 9999

Speed increasing ratio 2 to 5

r/min

Содержание BXII Series





















































Результаты поиска

Содержание BXII Series

Отзывы:

Бренды по названию

Популярные бренды

Orientalmotor BXII Series, Руководство по эксплуатации

Результаты поиска

Содержание BXII Series

Отзывы:

Бренды по названию

Популярные бренды