Orbitalum RA 41 Plus Скачать руководство пользователя страница 36

Страница: 36 / 40

8 Maintenance

Operating instructions RA 41 Plus (H)

(07.08)

MT_RA 41 Plus (H)_BA_04_790046773_04.doc

orbitalum tools

gmbh

8.1

Checking the level of the gear oil

Using the grip, turn the motor counter-clockwise from its home position by

approx. 120° until the marking (3) on the rotary element is in line with the
notch on the housing (approx. 8 o'clock position).

The oil level should be visible in the middle of the oil level viewglass (1).

8.2

Topping up gear oil

Check the oil level through the oil-level viewglass as described above and

top up with oil if necessary.

1. Undo the oil filler plug (2).

2. Fill with special Orbitalum Tools gear oil.

3. Keeping the motor in this position, check the oil level. Continue to top up

with oil until the oil level is visible in the middle of the oil level viewglass.

Topping up:

Содержание RA 41 Plus









































Результаты поиска

Содержание RA 41 Plus

Отзывы:

Похожие инструкции для RA 41 Plus

Бренды по названию

Популярные бренды

Orbitalum RA 41 Plus, Руководство по эксплуатации

Результаты поиска

Содержание RA 41 Plus

Отзывы:

Похожие инструкции для RA 41 Plus

Бренды по названию

Популярные бренды