Orbitalum GF 4 AVM Скачать руководство пользователя страница 43

Страница: 43 / 52

Operating instructions GF 4 (AVM / MVM)

7 Operation

orbitalum tools

gmbh

(01.08)

MT_GF 4_BA_04_790142762_01.doc

7.9

Processing the pipe manually

For processing the pipe with GF 4 AVM, see chapter 7.7, p. 32.
For GF 4 MVM, see chapter 7.8, p. 36.

7.9.1

Cutting the pipe manually

Danger of being injured by chips flying around

Never

work without the saw blade guard mounted.

Wear protective goggles.

If the pipe cutter was out of operation for a longer time:

–

Turn the cutter motor by 180°.

–

Switch the pipe cutter on and let it run for about 10 seconds.

This will lubricate all gear components.

1.  Set the pipe diameter (see chapter 7.4, p. 26).
2.  Adjust the length gauge (see chapter 7.5, p. 30).
3.  Adjust the saw blade to the pipe diameter (see chapter 7.4.1, p. 27).
4.  Tighten the hexagon nut of the saw blade fixture, if necessary

(see chapter 7.3, p. 25).

5. Adjust the spindle speed (see chapter 7.6, p. 31).
6. Push the pipe through the vice up to the desired length and clamp it. Support

pipes with a length of more than 1 m using a pipe feeder
(see chapter 7.4, p. 26).

Pull off the vice handle from the spindle before the slide housing starts rotating.

7. Apply saw blade lubricant to the saw blade:

–

up to 2": every 3 cuts,

–

over 2" and with chrome and high-quality steel pipes: after every cut.

Important:

If the pipe comes into contact with drinking water or foodstuffs,

only use Orbitalum Tools lubricating gel for saw blades.

For non-stop operation: after cutting, loosen the hexagon nut on the saw blade
to avoid damage caused by tension.

WARNING

Important

Note

Содержание GF 4 AVM





















































Результаты поиска

Содержание GF 4 AVM

Отзывы:

Похожие инструкции для GF 4 AVM

Бренды по названию

Популярные бренды

Orbitalum GF 4 AVM, Руководство по эксплуатации

Результаты поиска

Содержание GF 4 AVM

Отзывы:

Похожие инструкции для GF 4 AVM

Бренды по названию

Популярные бренды