Orbitalum GF 4 AVM Скачать руководство пользователя страница 38

Страница: 38 / 52

7 Operation

Operating instructions GF 4 (AVM / MVM)

(01.08)

MT_GF 4_BA_04_790142762_01.doc

orbitalum tools

gmbh

7.7.3

Beveling the pipe with GF 4 AVM

Danger of being injured by chips flying around

Never

work without the saw blade guard mounted.

Wear protective goggles.

If the pipe cutter was out of operation for a longer time:

–

Turn the cutter motor by 180°.

–

Switch on the AVM and the pipe cutter (see chapter 7.7.1, p. 32), let the
cutter motor run for about 10 seconds.

This will lubricate all gear components.

1.  Set the pipe diameter (see chapter 7.4, p. 26).
2.  Adjust the bevel cutter to the pipe diameter (see chapter 7.4.3, p. 29).
3.  Tighten the hexagon nut of the bevel cutter fixture, if necessary

(see chapter 7.3, p. 25).

4. Adjust the spindle speed and the feed force level (for standard values,

see chapter 7.6, p. 31).

5. Push the pipe through the vice up to the desired length and clamp it. Support

pipes with a length of more than 1 m using a pipe feeder (see chapter 7.4,
p. 26).

Pull off the vice handle from the spindle before the slide housing starts rotating.

6. Apply saw blade lubricant to the bevel cutter:

–

up to 2": every 3 cuts,

–

over 2" and with chrome and high-quality steel pipes: after every cut.

Important:

If the pipe comes into contact with drinking water or foodstuffs, only

use Orbitalum Tools lubricating gel for saw blades.

For non-stop operation: after beveling, loosen the hexagon nut on the bevel
cutter to avoid damage caused by tension.

7. Switch the pipe cutter on.
8. Press the START button .

Processing will now be started and will be stopped automatically after
a correct beveling process.

WARNING

Important

Note

Содержание GF 4 AVM





















































Результаты поиска

Содержание GF 4 AVM

Отзывы:

Похожие инструкции для GF 4 AVM

Бренды по названию

Популярные бренды

Orbitalum GF 4 AVM, Руководство по эксплуатации

Результаты поиска

Содержание GF 4 AVM

Отзывы:

Похожие инструкции для GF 4 AVM

Бренды по названию

Популярные бренды