manualshive.com logo in svg

Oracle X8-8, Руководство по установке

Поделиться
Скачать
Oracle X8-8 Скачать руководство пользователя страница 91

Configuring RAID

Configuring RAID

Some devices, including Oracle Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal

16 Port, must include a RAID volume before they can present a valid target for OS installation

programs.

The server is shipped with Oracle Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal

16 Port configured as RAID 0 volumes, meaning that each volume includes a single disk drive.

Other volumes combine multiple disks into arrays, which can increase performance and provide

redundancy.

To configure the Oracle Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal 16 Port

see 

“Configure RAID on Oracle Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal 16

Port” on page 92

.

Because altering RAID configuration might destroy any data or OS image on the affected

drives, you should back up any data on the drive, and you should create the volume before

installing an OS on it.

Supported Storage Devices

Your server might be equipped with one of the following storage devices:

■

Internal host bus adaptor (HBA) PCIe card and a combination of hard disk drives (HDDs)

and solid state drives (SSDs).
Oracle Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal 16 Port manages the

server's SSDs and HDDs, which are shipped configured as RAID 0 volumes.
For instructions to configure RAID on the internal HBA, see 

“Configure RAID on Oracle

Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal 16 Port” on page 92

.

■

Oracle Flash Accelerator F640 PCIe Cards. You can install an OS on these cards without

any additional configuration.
See 

“View Installed Oracle Flash Accelerator F640 PCIe Cards in BIOS Setup

Utility” on page 103

.

Configuring Storage Drives for Operating System Installation

91

Содержание X8-8







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды