manualshive.com logo in svg

Oracle X8-8, Руководство по установке

Поделиться
Скачать
Oracle X8-8 Скачать руководство пользователя страница 92

Configure RAID on Oracle Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal 16 Port

Configure RAID on Oracle Storage 12 Gb SAS PCIe RAID

Host Bus Adapter, Internal 16 Port

The Oracle Storage 12 Gb SAS PCIe RAID Host Bus Adapter, Internal 16 Port manages the

HDDs and SSDs in your system. When the system is shipped, the HDD and SSD drives are

configured into RAID 0 volumes. Use this procedure to reconfigure these into RAID volumes

according to your performance and redundancy needs.

Caution - 

Degraded Performance

. Combining HDD and SSD drives in the same array is

not recommended. An array with both HDDs and SSDs operates at HDD speed, which is

significantly lower than the speed of the SSDs.

1.

Configure the server for a one-time boot to BIOS.

a.   

Access the Oracle ILOM web interface.

b.   

Navigate to Host Management → Host Control.

c.   

Select 

BIOS

 from the drop-down list, and select 

Save

.

This causes the server to boot to BIOS on the next boot.

2.

Access a system console.

For more information, see 

“Redirect Host Server Desktop or Storage Devices” on page 83

 and

refer to 

Oracle X8 Series Servers Administration Guide

 at 

https://www.oracle.com/goto/

x86admindiag/docs

.

3.

Power on or reset the server.

For example, to reset the server:

■

From the local server,

 press the On/Standby button on the front panel of the server for

approximately 1 second to power off the server, and then press the On/Standby button again

to power on the server.

■

From the Oracle ILOM web interface,

 select 

Host Management 

→

 Power Control

, and

in the Select Action list box, select 

Power On

. Click 

Save

, and then click 

OK

.

■

From the Oracle ILOM CLI,

 type: 

reset /System

.

The system boots to the BIOS Setup Utility.

92

Oracle Server X8-8 Installation Guide • June 2019

Содержание X8-8







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды