Oracle Talari E100, Руководство по оборудованию

Страница: 28 / 41

2 8
Creating a Bootable USB Drive on Linux
Ensure that the capacity of your USB drive is at least 4 GB.
To create a bootable USB drive on Linux:
1. Download the E50 or E100 image from MOS.
2. Copy the image on the USB drive.
Doing this destroys all existing data on the USB drive.
3. Insert the USB drive into the computer and run the
dmesg|tail
command.
[4317966.832947] usb 4-1: new SuperSpeed USB device number 39 using
xhci_hcd
[4317966.845892] usb 4-1: New USB device found, idVendor=0951,
idProduct=1666
[4317966.845893] usb 4-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[4317966.845894] usb 4-1: Product: DataTraveler 3.0
[4317966.845895] usb 4-1: Manufacturer: Kingston
[4317966.845896] usb 4-1: SerialNumber: E0D55EA57419E3C139680956
[4317966.848319] usb-storage 4-1:1.0: USB Mass Storage device detected
[4317966.848421] scsi host6: usb-storage 4-1:1.0
[4317967.863955] scsi 6:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0
ANSI: 6
[4317967.864524] sd 6:0:0:0: Attached scsi generic sg4 type 0
[4317967.864606] sd 6:0:0:0: [sdd] 60604416 512-byte logical blocks: (31.0 GB/28.9 GiB)
[4317967.864790] sd 6:0:0:0: [sdd] Write Protect is off
[4317967.864792] sd 6:0:0:0: [sdd] Mode Sense: 45 00 00 00
[4317967.864972] sd 6:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't
support DPO or FUA
In this case, the device name is "sdd", and will be referenced by Linux as
“/dev/sdd”.
If Linux has been configured to auto-mount USB devices, unmount the partitions
on the drive. Run the “df” command to detect the status of the partitions of the
drive:
df
Filesystem 1K-blocks Used Available Use% Mounted on
devtmpfs 16416036 0 16416036 0% /dev
/dev/mapper/ol_lobi7u6-root 52403200 37842328 14560872 73% /
/dev/sda1 1038336 427060 611276 42% /boot
/dev/mapper/ol_lobi7u6-home 164415040 112140980 52274060 69% /home
/dev/sdd2 2755604 2389404 222896 92%
/run/media/oracle/USBBoot
In this example, the second partition of /dev/sdd is mounted and must be
unmounted. In your case there may be no mounts on the USB or more.
4. To unmount the partition on the drive, run the command:
umount
/run/media/oracle/USBBoot.
5. Run the df command again to make sure that there are no mounts matching your
USB device name (/dev/sdd in the example.)
6. Insert the USB drive. At this point, the USB drive is ready to receive the image.
7. gunzip the downloaded USB raw image file.
gunzip
d6000v1_OS_7_0_1_0_0_GA_02282020_OS_52_GA_05022019_R8_2_1_0_0_GA_01282020
.raw.gz