Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 47 / 258

Find the Server Serial Number

continue to operate your server with an empty slot, the server might overheat due to improper

airflow. For instructions on removing or installing a filler for a server component, refer to the

topic in this document about servicing that component.

Related Information

■

“Component Service Task Reference” on page 47

■

“Servicing SAS Drives” on page 85

■

“Servicing PCIe Cards” on page 169

Find the Server Serial Number

If you require technical support for your server, you must provide the chassis serial number.

You can find the chassis serial number on a sticker located on the front top of the server.

If it is not convenient to read either sticker, follow this procedure.

Access Oracle ILOM.

See

“Log In to Oracle ILOM (Service)” on page 26

Display the serial number.

show /System serial_number

/System
Properties:
serial_number = 1150CN2022
->

Related Information

■

“Safety Information” on page 44

■

“Component Service Task Reference” on page 47

■

“Accessing Internal Components” on page 55

Component Service Task Reference

This table identifies tasks for servicing components, including those that you must remove as

part of a service operation.

Preparing for Service

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды