Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 55 / 258

Accessing Internal Components

■

“Power Off the Server (Power Button - Graceful)” on page 51

■

“Power Off the Server (Emergency Shutdown)” on page 52

■

“Prevent ESD Damage” on page 55

■

“Connect AC Power Cords” on page 249

Accessing Internal Components

These topics provide procedures and guidelines when accessing internal components.

Step

Description

Link

Take antistatic precautions now.

“Prevent ESD Damage” on page 55

If necessary, remove the server from the rack.

“Remove a Server From the 4-Post, 19-inch

Rack” on page 56

“Remove a Server From the 2-Post, 19-inch

Rack” on page 63

Gain access to the internal components.

“Remove the Top Cover” on page 67

Related Information

■

“Safety Information” on page 44

■

“Service Tools” on page 46

■

“Component Service Task Reference” on page 47

■

“Removing Power From a Server” on page 49

Prevent ESD Damage

Many components housed within the chassis can be damaged by electrostatic discharge. To

protect these components from damage, perform these steps before opening the chassis for

service. See

“Safety Information” on page 44

Prepare an antistatic surface to set parts on during the removal, installation, or

replacement process.

Place ESD-sensitive components such as the printed circuit boards on an antistatic mat.

Preparing for Service

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды