Oracle DE2-24 Скачать руководство пользователя страница 186

Страница: 186 / 312

Servicing the 7x20 Controller

Input

■

Nominal frequencies: 50/60Hz

■

Nominal voltage range: 100-120/200-240 VAC

■

Maximum current AC RMS: 13.8A @ 100 VAC

■

AC operating range: 90-264 VAC

Output

■

3.3 VDC STBY: 3.0A

■

+12 VDC: 86.7A

Power Dissipation

■

Max power consumption: 1235.3 W

■

Max heat output: 4212 BTU/hr

■

Volt-Ampere rating: 1261 VA @ 240 VAC, 0.98P.F.

7120 Internal Boards

The chassis has the following boards installed.

Note -

Field-replaceable units (FRU) should only be replaced by trained Oracle service

technicians.

■

PCIe Risers:

Each riser supports two PCIe cards that are customer-replaceable. There are

two risers per system, each attached to the rear of the motherboard.

■

Motherboard:

The motherboard is a FRU and includes CPU modules, slots for 18 DIMMs,

memory control subsystems, and the service processor (SP) subsystem. The SP subsystem

controls the host power and monitors host system events (power and environmental). The

SP controller draws power from the host 3.3V standby supply rail, which is available

whenever the system is receiving AC input power, even when the system is turned off.

■

Power Distribution Board:

The power distribution board is a FRU and distributes main

12V power from the power supplies to the rest of the storage controller. It is directly

connected to the connector break out board and to the motherboard through a bus bar and

ribbon cable. It also supports a top cover interlock

kill

switch. The power supplies connect

directly to the power distribution board.

■

Connector Break Out Board:

The connector break out board is FRU and serves as the

interconnect between the power distribution board and the fan power boards, storage drive

backplane, and I/O board. It also contains the top-cover interlock "kill" switch.

■

Fan Power Boards:

The two fan power boards are FRUs and carry power to the system fan

modules. In addition, they contain fan module status LEDs and transfer I2C data for the fan

modules.

186

Oracle ZFS Storage Appliance Customer Service Manual • February 2016

Содержание DE2-24

























































































































































































































































































































Результаты поиска

Содержание DE2-24

Отзывы:

Бренды по названию

Популярные бренды

Oracle DE2-24, Руководство по обслуживанию клиентов

Результаты поиска

Содержание DE2-24

Отзывы:

Бренды по названию

Популярные бренды