background image

accordingly 

    5.8 Adjusting aperture diaphragm 
          Adjust  the  aperture  diaphragm  adjusting  shaft  for  condenser  till  the  position  which  stands  for  the 

magnification of objective 

         

adjust the aperture diaphragm 

          5.8.1  Adjust  the  aperture  diaphragm  by  the  adjusting  shaft.  The  brightness  and  resolution  will  be 

decrease  while  the  contrast  and  depth  of  view  will  increase  if  the  diameter  of  aperture 
diaphragm reduces 

          5.8.2. Adjust the value of aperture diaphragm to 70%

80% of the value of objective’s N.A. 

          5.8.3 The aperture diaphragm could control the N.A. of condenser. Do not adjusting the brightness by 

it while use the brightness adjusting knob to make the adjustment 

          5.8.4 N.A. is marked in each objective 
                    e.g. 40X/0.65 stands for that magnification is 40X and N.A. is 0.65 
          5.8.5 Remove the eyepiece and observe through the eye tubes by eyes directly   
                    N.A.  of  condenser  could  tell  users  the  position  of  aperture  diaphragm  adjusting  shaft  in 

corresponding magnification. (That is to say, the value of aperture diaphragm should be 70% to 
80%  of  the  N.A.  of  objective  when  the  aperture  diaphragm  adjusting  shaft  reaches  some 
position) If the objective has been changed, please move the shaft to the position with the same 
value which is in the objective in the optic path and this will make ideal contrast 

 
 
 
 
 
 
 
  5.9 Observing with oil immersion 
          There is “oil” marked in the oil immersion objective. Please use the oil immersion supplied by the 

manufacturer between the objective and cover glass 

          5.9.1 Operation 
                      5.9.1.1 Condenser 
                                    Remove the slide back and fall the condenser down   
a little. One drop of oil could be placed in the top of condenser by through   
the long aperture of stage. Then move the slide forward and lift the condenser   
up 
                      5.9.1.2 Objectives 
                                    Turn the nosepiece and take the objective out of the   
optic path. Place one drop of oil on the slide then turn the condenser slowly   
and mount the objective 
        5.9.2 Air bubble in oil immersion 
                  5.9.2.1 Never make the oil immersion into your eyes. Please take following steps as soon as the 

oil immersion touches your skin or eyes 

                                Use soap or clean water to wash your skin carefully 
                                Please  wash  your  eyes  with  clean  water  (at  least  wash  15  minutes)  and  go  to  the 

hospital at once 

                  5.9.2.2 Do not expose the oil immersion in the sun or ultraviolet radiation directly 

Содержание A12.1010

















Отзывы: