background image

CHAPTER 1: SNAP PAC SNAP-IT-PM INSTALLATION GUIDE

Form 1698-070427—SNAP PAC SNAP-IT-PM Installation Guide

7

7

Removing a Module

To remove a module from the SNAP-IT unit, 
you must use the SNAP module tool 
(provided).

1.

Unplug power to the SNAP-IT unit. 
Remove the small white fuse from the 
module mounting rack. 

WARNING: 

Make sure there is no power to 

the rack before continuing, or you may 
severely damage the module.

2.

If the modules are held in place with 
screws, remove them.

3.

Holding the SNAP module tool as 
shown in the illustration at right, insert 
it into the notch at the base of the 
module.

4.

Squeeze the module tool against the 
module to open the release latch. Pull 
straight out on the module (the opposite direction from the rack) to remove it.

5.

When you have finished removing and installing modules, replace the small white fuse on the 
module mounting rack and plug power back into the SNAP-IT unit.

Notes on Maintenance and Troubleshooting

Instructions for maintenance and troubleshooting are in the 

PAC Manager User’s Guide

 and in the 

controller or brain user’s guide.

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES

 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • [email protected] • 

SUPPORT

 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • [email protected]

© 2007 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

Содержание SNAP PAC SNAP-IT-PM Series









Отзывы: