OPTIKON I.V. Скачать руководство пользователя страница 17

I.V. Pole cart 

Installation and operating manual 

OPTIKON 2000 

Code 181004EN 

 

2007-10-09 Rev. 0 

 

6-1

6.  INSTALLATION AND OPERATING PROCEDURE 

6.1 INTRODUCTION 

This section details a recommended installation and operational checkout procedure for 
the Optikon Equipment Cart 181004.  

The operational checks, however, which are performed after the system installation to 
verify instrument operation, must be performed exactly as indicated and should not be 
regarded as recommended practice or as encouragement for surgical operating room 
procedures.

 

To bring your system in operation, a series of cable and tubing connections between cart 
and control console, footswitch, handpieces and I/A system must be made.

 

Follow the installation and operating instructions carefully in a step by step manner and, 
within a short time, you will have gained all the knowledge needed for successful operation 
of your surgery system. 

6.2 INITIAL 

INSPECTION 

 
This instrument was carefully inspected, mechanically and electrically, prior to shipment. 
Before unpacking the OPTIKON Equipment Cart, inspect the carton for damage. If it is 
damaged, be especially careful when inspecting the contents for any mechanical damage 
which may have occurred during shipment, and test the electrical performance. If physical 
damage is found, you should apply at once to the carrier that handled the consignment  
(mail, railways or forwarding agents) and have an appropriate certificate established. 
If damage of a mechanical nature is discovered or if the instrument does not match the 
specifications, immediately inform the shipping company and the nearest OPTIKON 
service center, which will repair or replace the instrument. 
 
 

Содержание I.V.






















Отзывы: