OPTIKON I.V. Скачать руководство пользователя страница 14

I.V. Pole cart 

Installation and operating manual 

OPTIKON 2000 

Code 181004EN 

 

2007-10-09 Rev. 0 

 

5-2

 
POWER (ON/OFF MAINS SWITCH/PILOT LAMP)  

This illuminated switch is located on the left side of the cart and controls both the internal 
electric I.V. pole and the power outlets for the control panels on the cart. Provided that the 
mains switches of the single consoles are left to the on position, this switch will energize or 
de-energize all the surgical system. 

 

PROTECTION COVER 

This protection cover, located at the rear of the cart, was designed to prevent the use of 
the cart's power outlets to connect any device other than approved Optikon instruments. 
The lid must be removed by a qualified technician when the

 console is first installed

The 

lid must be restored in place once the equipment has been installed

. The following are 

located under the protection cover (Fig. 1): 

 

 

1. 

MAINS POWER CONNECTION FOR HOSTED CONSOLES. 

Three mains sockets allow connecting the mains power for the hosted surgical 
consoles. 

2. 

INTERFACE CONNECTOR

 

 

It allows the position control of the integral electric I.V. pole by the hosted 

 

console. The console connects here by the means of the signal cable supplied 

 

with the cart. 

3. 

FOOTSWITCH CONNECTOR

 

 

The bottle Up/Down rocker footswitch connects here. 

4. 

MAINS INLET AND FUSE HOLDER

 

 

The power cord to energize the cart must be connected to this inlet. Use only the 

 

supplied cord or a Medical grade power cord. The socket also hosts two fuses that 

 

interrupt the mains power in case of fault in the cart or in the hosted consoles. 

5. 

VOLTAGE SETTING CONNECTOR

 

By turning the voltage setting connector to the proper position, it is possible to set 
the mains voltage (220 or 110 V). 

 

 

 

TAG (MARKINGS

Provides serial number, electrical rating and other information as required by EN 60601-1 
 
 

 

 

Содержание I.V.






















Отзывы: