Opticon OPR 3001 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 42

Opticon OPR 3001 Скачать руководство пользователя страница 10

Opticon

OPR 3001

Specifications Manual

10

6. Optical

Specifications

6.1. Laser Scan Specifications

Parameter Specification

Unit

Light-emitting element

Red laser diode

—

Emission wavelength

650 ±10 (25° C)

nm

Light output

1.0 or less

mW

Scanning method

Bi-directional scanning

—

Scanning speed

100 ±20

scans/s

Scan angle: 54 ±5

°

Scan angle

Read angle: 44 (Min)

°

Auto-trigger IR detection area

40

mm

Notes:

Refer to chapter 15, “Trigger and Read Options,” to read about the scan modes.

Refer to chapter 7, “Technical Specifications,” to read about scanning performance.

6.1.1.

Tilt of Laser Scan Line

Laser scanning tilt is the vertical difference between both ends of a laser scan
line. Measure it in the middle of the laser scan line.
Maximum tilt between both ends of laser scan line: Less than 1.2° upward tilt from
the scan origin.
Maximum of 3.1 mm when measured at a point 150 mm away from the scan
origin. (The skew angle of this measurement was zero degrees.)

«
...
8
9
10
11
12
...
»

Содержание OPR 3001











































Отзывы:

Нет отзывов