background image

 

HOBO RX3000 Remote Monitoring Station Manual 

 

22 

Fault 
Code # 

Description 

Action to Take 

Removing Smart Sensors

). Also check 

that the smart sensor cables are ok. 

132 

Analog 
Excitation 
Bus Fault 

Check the analog sensor connection 
and the excitation settings for the 
sensor in HOBOlink. 

Battery Information 

The station uses one rechargeable 4 volt, 10Ah, sealed lead-
acid battery. Use the AC adapter (AC-U30), solar panel (SOLAR-
xW), or external DC power cable (CABLE-RX-PWR) with your 
own charging device to keep the battery charged. If using a 
solar panel, the quality and quantity of solar light can affect 
whether the battery is sufficiently charged to last through the 
night and cloudy periods. Without a charging device connected, 
expected battery life varies based on the ambient temperature 
where the station is deployed, the logging or sampling interval, 
frequency of connections to HOBOlink, the number of channels 
that are active, excitation in analog modules, the number of 
tripped alarms, and other factors. Deployments in extremely 
cold or hot temperatures, a logging interval faster than 1 
minute, or a sampling interval faster than 15 seconds can 
impact battery life. Estimates are not guaranteed due to 
uncertainties in initial battery conditions and operating 
environment. 

Use the following table as a guideline for estimating how long 
the station will run using a fully charged battery and no source 
of external power. For these examples, the station has up to 10 
smart sensors installed and no excitation enabled for the 
analog sensor module. 

Connection Interval 

Logging Interval 

Typical Run Time 

10 minutes 

1 minute 

20 days 

1 hour 

15 minutes 

50 days 

6+ hour 

30 minutes 

75 days 

 
All communications will stop if the battery voltage drops below 
3.9 V. The station will stop logging if the battery voltage drops 
below 3.6 V. If the station has stopped logging due to low 
battery voltage, plug in an AC adapter, solar panel, or external 
power source to recharge it. It may take several minutes for the 
station to power back up; the lower the remaining voltage, the 
longer it will take for power to return. Also note that it will take 
longer for power to return with a solar panel than with an AC 
adapter. If the charging device is not recharging a dead battery, 

Important:

 Due to the self-discharge characteristics of this type 

of battery, it is imperative that you charge the battery for at 
least 12 hours every six months at minimum, even if you are 
not actively using the station. Otherwise, permanent loss of 
battery capacity may occur. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

www.

.com

[email protected]

1.800.561.8187

Содержание HOBO RX3000 Series


































Отзывы: