94
Troubleshooting
—Continued
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
• On the TX-SR507, while Powered Zone 2 is being
used, nothing is output by these speakers (page 81).
The surround back speakers produce no sound
• Depending on the current listening mode, no sound
may be produced by the surround back speakers. Try
another listening mode (page 59).
• Not much sound may be produced by the surround
back speakers with some sources.
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
• On the TX-SR507, while Powered Zone 2 is being
used, playback in the main room is reduced to 2.1-
channels and the center, surround speakers produce no
sound (page 80).
• On the TX-SR577, while Powered Zone 2 is being
used, playback in the main room is reduced to 5.1-
channels and the surround back speakers produce no
sound (page 80).
The subwoofer produces no sound
• If the source material contains no audio in the LFE
channel, the subwoofer produces no sound.
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 66 or 68).
The Zone 2 speakers produce no sound
• The Zone 2 speakers only output sources that are
connected to an analog input. Check to see if the
source component is connected to an analog input.
• On the TX-SR577, “Powered Zone 2” cannot be used
if “Sp Type” is set to “Bi-Amp” (page 40).
There’s no sound with a certain signal format
• Check the digital audio output setting on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
• With some DVD-Video discs, you need to select an
audio format from a menu or with the [AUDIO] button
on your DVD player’s remote controller.
Can’t get 6.1- or 7.1-channel playback
• On the TX-SR507, while Powered Zone 2 is being
used, playback in the main room is reduced to 2.1-
channels and the center, surround speakers produce no
sound (page 80).
• On the TX-SR577, while Powered Zone 2 is being
used, playback in the main room is reduced to 5.1-
channels and the surround back speakers produce no
sound (page 80).
Can’t select the Pure Audio listening mode
• The Pure Audio listening mode cannot be selected
while Zone 2 is on.
• The Pure Audio listening mode is not available on the
North American / Taiwan models.
The volume cannot be set to 79
• Check to see if a maximum volume has been set
(page 75).
• If the volume level of each individual speaker has been
adjusted to high positive values (page 69), then the
maximum master volume possible may be reduced.
Note that the individual speaker volume levels are set
automatically after the Audyssey 2EQ™ Room Cor-
rection and Speaker Setup function has been com-
pleted (page 37).
• After the Audyssey 2EQ™ Room Correction and
Speaker Setup function has been run, or the volume
level of each individual speaker has been adjusted
(pages 37 and 69), the maximum volume may be
reduced.
• When the levels of each speaker have been adjusted
(page 69), the maximum possible volume may be
reduced.
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on can degrade audio
performance, so don’t use them.
• An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
• Make sure that the source is Dolby Digital (page 78).
About DTS signals
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.
• When DTS program material ends and the DTS
bitstream stops, the AV receiver remains in DTS
listening mode and the DTS indicator remains on. This
is to prevent noise when you use the pause, fast
forward, or fast reverse function on your player. If you
switch your player from DTS to PCM, as the AV
receiver does not switch formats immediately, you may
not hear anything, in which case you should stop your
player for about 3 seconds, and then resume playback.
• With some CD players, you won’t be able to playback
DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t
recognize it as a genuine DTS signal. In such cases,
you may hear noise.
The beginning of audio received by an HDMI IN
can’t be heard
• Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio
signals, sound may not be output immediately.
There’s no picture
• Make sure that all video connecting plugs are pushed
in all the way (page 22).
• Make sure that each video component is properly
connected.
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
• While the Pure Audio listening mode is selected, the
video circuitry is turned off and only the HDMI OUT
outputs video signals.
Video
Содержание TX SR507 - AV Receiver
Страница 99: ...99 Memo ...
