Onkyo HT-RC560, Руководство пользователя

Страница: 56 / 140

Advanced Operations
En-56
Operating
procedure
(
➔
page 52 )
by the subwoofer instead of the speaker. Refer to
your speaker’s manuals to determine the optimum
crossover frequencies.
■
Subwoofer
`
Yes
`
No
■
Front
`
Full Band
`
40Hz to 100Hz , 120Hz , 150Hz , 200Hz
Note
• If the “ Subwoofer ” setting is set to “ No ”, the “ Front ” setting
is fixed at “ Full Band ”.
■
Center
*1
, Surround
*1
`
Full Band
`
40Hz to 100Hz , 120Hz , 150Hz , 200Hz
`
None
■
Front High
*1*2*3*5
`
Full Band
`
40Hz to 100Hz , 120Hz , 150Hz , 200Hz
`
None
■
Surround Back
*1*2*3*4
`
Full Band
`
40Hz to 100Hz , 120Hz , 150Hz , 200Hz
`
None
Note
*1 “ Full Band ” can be selected only when “ Full Band ” is
selected in the “ Front ” setting.
*2 If the “ Surround ” setting is set to “ None ”, this setting
cannot be selected.
*3 If the “ Speakers Type (Front) ” setting is set to
“ Bi-Amp ”, or the “ Powered Zone 2 ” setting is set to
“ Yes ” together with Zone 2 turned on, this setting cannot
be selected.
*4 If anything else than “ None ” is selected in “ Front High ”,
this setting is automatically set to “ None ”.
*5 If anything else than “ None ” is selected in “ Surround
Back ”, this setting is automatically set to “ None ”.
■
Surround Back Ch
`
1ch :
Select if only one surround back speaker L is
connected.
`
2ch :
Select if two (left and right) surround back
speakers are connected.
Note
• If the “ Surround Back ” setting is set to “ None ”, this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
`
80Hz , 90Hz , 100Hz , 120Hz
`
Off :
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff
frequency of the LFE channel’s low-pass filter
(LPF), which can be used to filter out unwanted
hum. The LPF only applies to sources that use the
LFE channel.
■
Double Bass
`
On
`
Off
Turn this setting on to boost bass output by feeding
bass sounds from the front left, right, and center
channels to the subwoofer. Default setting: “
- - - -
”
Note
• When the “ Subwoofer ” setting is set to “ No ” or the “ Front ”
setting to anything other than “ Full Band ”, this setting is
fixed to “ - - - ”.
• This setting is set to “ On ” automatically when the
“ Subwoofer ” and “ Front ” settings are set for the first time
to “ Yes ” and “ Full Band ” respectively.
Speaker Distance
Here you can specify the distance from each speaker
to the listening position so that the sound from each
speaker arrives at the listener’s ears as the sound
designer intended.
■
Unit
`
feet :
Distances can be set in feet. Range: 1.0ft to
30.0ft in 1.0 foot steps.
`
meters :
Distances can be set in meters. Range: 0.30m
to 9.00m in 0.30 meter steps.
(The default setting varies from country to country.)
■
Left, Front High Left, Center, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
`
Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “ No ” or “ None ” in
“Speaker Configuration” cannot be selected (
➔
page 55 ).
• When the “ Powered Zone 2 ” setting is set to “ Yes ” and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.
This setting is NOT set automatically by
Audyssey MultEQ ® Room Correction and Speaker
Setup function (
➔
page 24 ).
This setting is set automatically by
Audyssey MultEQ Room Correction and Speaker
Setup function (
➔
page 24 ).