manualshive.com logo in svg

Omron ZX-CAL, Инструкции по эксплуатации, Страница: 67 / 187

Поделиться
Скачать
Omron ZX-CAL Скачать руководство пользователя страница 67

Reflective Sensor Heads: FUN Mode Functions

Section 3-5

47

Displaying the Height of the Sensing Object: One-point Scaling B

The height of the sensing object can be displayed by using one-point scal-
ing and inverting the display values. 

When the display values are inverted, the larger the displacement, the
smaller the display value. Therefore, the height of the sensing object can
be displayed after inputting the height of a known sensing object.

Because one-point scaling is used, the range of display values is not
changed. The linear output also remains unchanged.

Example:

Example: One-point Scaling B

100.0

80.0

100.0

110.0

70.0

110.0

120.0

60.0

120.0

130.0

50.0

130.0

Sensor Head

X

Y

 Although the Y value 

must be displayed, the 

X value is displayed.

If X = 110 mm
and Y = 70 mm,

Measured value = Display value

Measured value

Display value

: Scaling value input

110 mm is displayed as 70 mm 

and 

the display values

 are inverted.

Display value

(mm)

110.0

70.0

110.0

Actual distance (mm)

Even though the display values

are offset and inverted, the

range of display values remains 

unchanged.

Sensing object

All display values are offset

and inverted.

Z157-E1-01C.book  Page 47  Thursday, August 31, 2006  5:13 PM

Содержание ZX-CAL




























































































































































































Отзывы:

Нет отзывов