manualshive.com logo in svg

Omron ZX-CAL, Инструкции по эксплуатации, Страница: 162 / 187

Поделиться
Скачать
Omron ZX-CAL Скачать руководство пользователя страница 162

Error Displays

Section 5-1

142

5-1

Error Displays

5-1-1

Error Displays during Normal Measurement

Note

1.

Although teaching is impossible, threshold values can be input directly
even for an insufficient incident level, an incident level saturation, or a
distance measurement error.

2.

The display priority is in descending order from the top of the above
table when more than one error occurs at the same time.

3.

The error is displayed only for a Reflective Sensor Head.

Display

Cause and countermeasure

Recovery

(Flashing)

One or all of the judgement outputs are short-cir-
cuited.

→

 Clear the load short-circuit.

Automatic 
recovery

(Flashing)

EEPROM destruction or data error

→

 Press the ENT Key for 3 seconds or longer.

→

 Replace the Amplifier Unit if the above counter-

measure does not solve the problem.

Automatic 
recovery or 
replacement

(Flashing)

The Sensor Head is disconnected or there is a 
Sensor Head error.

→

 Connect the Sensor Head.

→

 Replace the Sensor Head if the above counter-

measure does not solve the problem.

Automatic 
recovery or 
replacement

(Flashing)

(See note 3.)

Incident level insufficient or distance measurement 
error (Refer to 5-2-5.)

→

 Optimize the gain setting or select the AUTO 

mode when changing the gain setting.

→

 Change to an appropriate workpiece if the 

above countermeasure does not solve the problem.

Automatic 
recovery

(Flashing)

(See note 3.)

Incident level saturation or distance measurement 
error (Refer to 5-2-5.)

→

 Optimize the gain setting or select the AUTO 

mode when changing the gain setting.

→

 Change to an appropriate workpiece if the 

above countermeasure does not solve the problem.

Automatic 
recovery

(Flashing)

(See note 3.)

Distance error

→

 Set the workpiece within the measurable range.

Automatic 
recovery

Z157-E1-01C.book  Page 142  Thursday, August 31, 2006  5:13 PM

Содержание ZX-CAL




























































































































































































Отзывы:

Нет отзывов