Omron ZX-CAL Скачать руководство пользователя страница 165

Страница: 165 / 187

Setting Problems

Section 5-2

145

5-2-5

Distance Measurement Errors

These errors are displayed only for a Reflective Sensor Head.

A distance measurement error indicates the inability to carry out measure-
ment due to an incident level error. This occurs in the following cases:

5-2-6

Laser Deterioration

will be displayed on the main display for 5 seconds when

the power is turned ON if the Sensor Head laser has deteriorated. Replace
the Sensor Head.

Insufficient incident
level:

The incident level may be insufficient when the
sensing object reflectivity is extremely small, such
as for black rubber.

Incident level satura-
tion:

The incident level may be saturated when the
sensing object reflectivity is extremely large, such
as for a mirror.

Distance error:

An error may occur when the sensing object is
outside the sensing range and the reflected light
does not arrive at the correct receiver position.

Z157-E1-01C.book Page 145 Thursday, August 31, 2006 5:13 PM

Содержание ZX-CAL




























































































































































































Результаты поиска

Содержание ZX-CAL

Отзывы:

Omron ZX-CAL, Инструкции по эксплуатации, Страница: 165 / 187

Результаты поиска

Содержание ZX-CAL

Отзывы: