Omron STC-MBS123BU3V Скачать руководство пользователя страница 61

Страница: 61 / 64

No.16S121-03

61/64

STC-MBS891U3V / STC-MCS891U3V / STC-MBS123BU3V / STC-MCS123BU3V
Product Specifications and Use’s Guide

Name

Description

GainSelector

Selects which Gain is controlled by the various Gain features.

Gain

Controls the selected gain as an absolute physical value. This is an amplification factor
applied to the video signal.

GainAuto

Sets the automatic gain control (AGC) mode. The exact algorithm used to implement
AGC is device-specific.

GainAutoLimitMax

Determine the upper limit of gain when GainAuto is set to Continuous.

GainAutoLimitMin

Determine the lower limit of gain when GainAuto is set to Continuous.

AutoLightTarget

Determine the brightness target for GainAuto.

BlackLevelSelector

Selects which Black Level is controlled by the various Black Level features.

BlackLevel

Controls the black level as an absolute physical value. This represents a DC offset
applied to the video signal.

BalanceRatioSelector

Selects which Balance ratio to control.

BalanceRatio

Controls ratio of the selected color component to a reference color component. It is used
for white balancing.

BalanceWhiteAuto

Controls the mode for automatic white balancing between the color channels. The white
balancing ratios are automatically adjusted.

Name

Description

PixelCorrectionAllEnabled

Enable pixel correction for all pixels.

PixelCorrectionIndex

Determine index of targeted pixel for pixel correction.

PixelCorrectionEnabled

Determine if targeted pixel is enabled for pixel correction.

PixelCorrectionX

Determine x-coordinate of targeted pixel for pixel correction.

PixelCorrectionY

Determine y-coordinate of targeted pixel for pixel correction.

Name

Description

UserSetSelector

Selects the feature User Set to load, save or configure.

UserSetLoad

Loads the User Set specified by UserSetSelector to the device and makes it active.

UserSetSave

Save the User Set specified by UserSetSelector to the non-volatile memory of the
device.

UserSetDefault

Selects the feature User Set to load and make active by default when the device is reset.

Содержание STC-MBS123BU3V

































































Результаты поиска

Содержание STC-MBS123BU3V

Отзывы:

Похожие инструкции для STC-MBS123BU3V

Бренды по названию

Популярные бренды

Omron STC-MBS123BU3V, Технические характеристики и руководство пользователя

Результаты поиска

Содержание STC-MBS123BU3V

Отзывы:

Похожие инструкции для STC-MBS123BU3V

Бренды по названию

Популярные бренды