Omron SMARTSLICE - 04-2008 Скачать руководство пользователя страница 92

Страница: 92 / 122

Reading the Error History with the DeviceNet Configurator

Section 6-3

Communications Unit
Error History

Slice Bus Error
History

Error

code

(Hex)

Contents

Details

Saved in error

history when

power goes OFF?

Corrective action

1st byte

2nd byte

0002

WDT error

0x00

Yes

Replace the Unit if the error
occurs frequently.

0370

Verification error (Slave miss-
ing)

Connect the missing Unit and
restart.

0372

Verification error (unregistered
Slave joined network)

0x80:
Slice I/O

Node address
(Hex)

Remove the unregistered
Unit and restart.

021A

Setting table logic error

Cause:
There was a checksum error in
on of the following tables or a
set value was out-of-range.

• Network parameters
• Registration table
• Slave parameters
• Backup restore data

0x00

0x0A: Registra-
tion table

0x0B: Slave
parameters

0x0C: Network
parameters

0x0F: Backup
restore data

Yes

Download the settings again.

0602

Memory access error

Cause:

• A hardware error occurred in

the Unit’s internal non-vola-
tile memory.

• E2P hardware error
• Backup communications fail-

ure

• FROM save failure
• EEPROM save failure
• FROM hardware error
• ADR failure (communications

failure)

0x01:
Read
error

0x02:
Write
error

0x07: Error his-
tory

0x09: Identity
information

0x0A: Registra-
tion table

0x0C: Network
parameters

0x0F: Backup
restore data
(E2P/FROM)

Yes (No for error
history only)

Replace the Unit if the error
occurs frequently.

Error

code

(Hex)

Contents

Details

Saved in error

history when

power goes OFF?

Corrective action

1st byte

2nd byte

0300

Backup data reception error

0x80:
Slice I/O

Node address
(Hex)

Verify that the Unit is con-
nected properly. Check
whether there is excessive
noise in the surroundings.

0374

Transmission error

Cause:
A transmission error occurred.

0x80:
Slice I/O

Node address
(Hex)

Verify that the Unit is con-
nected properly. Check
whether there is excessive
noise in the surroundings.

0375

Communications stopped due
to a transmission error.

Cause:
The Unit is set to stop commu-
nications for communications
errors and a transmission error
occurred. (Error code 0374 will
not occur in this case.)

0x80:
Slice I/O

Node address
(Hex)

Yes

Verify that the Unit is con-
nected properly. Check
whether there is excessive
noise in the surroundings.

Содержание SMARTSLICE - 04-2008



























































































































Результаты поиска

Содержание SMARTSLICE - 04-2008

Отзывы:

Бренды по названию

Популярные бренды

Omron SMARTSLICE - 04-2008, Руководство по эксплуатации

Результаты поиска

Содержание SMARTSLICE - 04-2008

Отзывы:

Бренды по названию

Популярные бренды