Omron SMARTSLICE - 04-2008 Скачать руководство пользователя страница 89

Страница: 89 / 122

LED Indicators and Error Processing

Section 6-2

DeviceNet
Communica-
tions Unit,
continued

Green

The Slice bus is operating
normally.

---

Power is not being supplied to
the Unit.

Check whether power is being supplied by
the Unit power supply.

Red

Slice I/O Unit configuration
error occurred.

Check the following items.

• Are more than 64 I/O Units connected?
• Are more than 128 bytes of I/O data being

used?

• Has the I/O configuration changed since

the I/O configuration table was registered?

Red

(for 2 s)

Backup operation failed.

Backup the data again.

Restore operation failed.

Reinstall the Unit in which the data was
being restored and turn the power ON
again.

Red

Slice bus communications
error occurred.

Check whether the Slice I/O Terminal’s
base block is connected properly.

When the registration table
function is enabled, the actual
configuration does not match
the registered configuration.

Correct the configuration and turn the
power ON again.

Green

The total number of I/O points
in the Slice I/O Terminals
exceeds the maximum.

Correct the Unit configuration and number
of I/O points and turn the power ON again.

Restore operation in progress Wait until the restore operation is com-

pleted.

Backup operation in progress

Wait until the backup operation is com-
pleted.

Joining nodes to network

Wait until the nodes have been added to the
network.

UNIT
PWR

Green

Unit power supply is providing
power normally.

---

Unit power supply is not being
supplied to the Unit.

Check whether power is being supplied by
the Unit power supply.

IO
PWR

Green

I/O power supply is providing
power normally.

---

I/O power supply is not being
supplied to the Unit.

Check whether power is being supplied by
the I/O power supply.

Slice I/O Units TS

Green

Slice I/O Unit operating nor-
mally.

---

Unit power supply is not being
supplied to the Unit.

Check whether power is being supplied by
the Unit power supply.

Red

Unit hardware failure

Turn the power OFF and then ON again.
Replace the Unit if the error recurs.

Communications error
occurred.

Check whether the connector is inserted
properly.

Green

Restore operation in progress Wait until the restore operation is com-

pleted.

Backup operation in progress

Wait until the backup operation is com-
pleted.

GRT1-PD2
I/O Power
Supply Unit

IO
PWR

Green

I/O power supply is providing
power normally.

---

I/O power supply is not being
supplied to the Unit.

Check whether power is being supplied by
the I/O power supply.

Unit

LED

name

Color

Status

Meaning

Likely cause of error

Содержание SMARTSLICE - 04-2008



























































































































Результаты поиска

Содержание SMARTSLICE - 04-2008

Отзывы:

Бренды по названию

Популярные бренды

Omron SMARTSLICE - 04-2008, Руководство по эксплуатации

Результаты поиска

Содержание SMARTSLICE - 04-2008

Отзывы:

Бренды по названию

Популярные бренды