manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Руководство по эксплуатации

Поделиться
Скачать
Omron SMARTSLICE - 04-2008 Скачать руководство пользователя страница 72

53

Preparation for Operation

Section 4-2

4-1-2

Example System Configuration

This section explains the operating procedure for the following minimal sys-
tem configuration. Connect the communications cable between the DeviceNet
Master Unit and DeviceNet Communications Unit after connecting the desired
Slice I/O Units to the DeviceNet Communications Unit.

4-2

Preparation for Operation

4-2-1

Determining the Slice I/O Terminal’s I/O Specifications

A single GRT1-DRT DeviceNet Communications Unit can control up to 64
Slice I/O Units with up to 1,024 I/O bits (64 words). In this example the Slice I/
O Terminal has the following configuration.

• 16 inputs

• 16 outputs

4-2-2

Selecting the Slice I/O Units

The following devices were selected, as shown in the basic system configura-
tion in 

4-1-2 Example System Configuration

.

Master Unit: CS1W-DRM21-V1
DeviceNet Communications Unit: GRT1-DRT1
Slice I/O Units: Four GRT1-ID4, four GRT1-OD4, and one GRT1-END

Note

OMRON has a wide variety of DeviceNet compatible Master Units and Slave
Units available. Select the best Units for your application.

4-2-3

Confirming Specifications

Number of I/O Points Less 
Than 1,024 (64 Words)

Verify that the total number of I/O points is less than the maximum of 1,024
points (64 words). This example uses the following calculation:

4 Units × 4 inputs (16 points) + 4 Units × 4 outputs (16 points) = 32 points

Power Consumption Less 
Than 80 W/Block

Verify that the power consumption is less than 80 W per block. This example
uses the following calculation:

1 GRT1-DRT Unit × 3 W =  3 W
4 GRT1-ID4 Units × 1 W =  4 W
4 GRT1-OD4 Units × 1 W = 4 W

Total = 

11 W

DeviceNet 

GRT1-DRT DeviceNet
Communications Unit

Slice I/O Terminal

GRT1-END
End Unit

DeviceNet Configurator

CS1W-DRM21-V1
DeviceNet Master Unit

GRT1-ID4

GRT1-OD4

Содержание SMARTSLICE - 04-2008



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды