Omron SMARTSLICE - 04-2008 Скачать руководство пользователя страница 25

Страница: 25 / 122

List of Available Units

Section 1-4

1-4

List of Available Units

The following table shows the Units that can be used in Slice I/O Terminals as
well as the devices that can be connected. Refer to the

GRT1 Series Slice I/O

Units Operation Manual

for details, such as Slice I/O Unit specifications.

Switches

Node-address
setting switches

Decimal rotary switches

Set the Unit’s node address as a DeviceNet Slave.

Other switches

DIP switch

Pin 1: Create/Enable registered table (Switch from
OFF to ON to register the table. Leave ON to enable
the table.)

Pin 2: Always OFF.

Pin 3: Automatic restore (Auto-restore enabled when
ON.)

Pin 4: Backup trigger (Switch from OFF to ON two
times to backup the parameter data.)

Connector

One open connector for DeviceNet, with screws

The XWG4-05C4-TF-D Multi-drop Connector can be
connected.

Terminals

Two terminals for I/O power supply
Two terminals for Unit power supply

Power consumption

3 W

Power consumption per block

80 W max. (Unit power supply)

(If more than 80 W is required, separate into blocks
using Turnback Units.)

Block separation

Basic block plus up to two other blocks

I/O current consumption

4 A max.

Weight

137 g

Accessories

XW4G-05C4-TF-D Connector

For multi-drop node connection. Connector screws
provided.

Item

Specification

Model

number

Specifications

GRT1-DRT

DeviceNet Communications Unit (Up to 64 I/O Units can be con-
nected.)

GRT1-ID4

Slice I/O Unit with 4 DC inputs (NPN)

GRT1-ID4-1

Slice I/O Unit with 4 DC inputs (PNP)

GRT1-OD4

Slice I/O Unit with 4 DC outputs (NPN)

GRT1-OD4-1 Slice I/O Unit with 4 DC outputs (PNP)

GRT1-ROS2

Slice I/O Unit with 2 relay outputs

GRT1-AD2

Slice I/O Unit with 2 analog inputs

GRT1-DA2V

Slice I/O Unit with 2 voltage analog outputs

GRT1-DA2C

Slice I/O Unit with 2 current analog outputs

GRT1-END

End Unit

GRT1-PD2

I/O Power Supply Unit

GRT1-TBR

Right Turnback Unit (Mounts to the right side of I/O Terminal.)

GRT1-TBL

Left Turnback Unit (Mounts to the left side of I/O Terminal.)

GCN2-100

Turnback Cable (1 m)

Содержание SMARTSLICE - 04-2008



























































































































Результаты поиска

Содержание SMARTSLICE - 04-2008

Отзывы:

Бренды по названию

Популярные бренды

Omron SMARTSLICE - 04-2008, Руководство по эксплуатации

Результаты поиска

Содержание SMARTSLICE - 04-2008

Отзывы:

Бренды по названию

Популярные бренды