Omron NYB17-11 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 244

background image

I/O Connector Wiring Procedure

Use the following procedure to wire the I/O connector.

1

Remove the sheath from the wires.

7 mm

Precautions for Safe Use

Observe the following precautions to prevent broken wires.
• When you remove the sheath, be careful not to damage the conductor.
• Connect the conductor without twisting the wires.
• Do not weld the conductors. Doing so may cause the wires to break with vibration.

2

Remove the I/O connector from the Box PC.

3

Insert a screwdriver in the small groove above the cable entry

1

to unlock the cable entry and

then push the wire all the way to the back of the cable opening

2

.

1

2

4

Remove the screwdriver.

Do not apply stress to the cable after you have connected the wires.

5 Installation

5 - 39

NY-series Industrial Box PC User's Manual (W553)

5-4
W
ire

5

5-4-4 Wire the I/O Connector

«
...
145
146
147
148
149
...
»

Содержание NYB17-11





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NYB17-11

Бренд: M-system Страницы: 3

Бренд: NARGESA Страницы: 34

Бренд: Ultraflex Страницы: 3

BOBCAT 130 Series

Бренд: Balcrank Страницы: 12

Бренд: uhlmann & zacher Страницы: 23

Бренд: SCHUNK Страницы: 32

Бренд: Nodka Страницы: 50

Бренд: Mold-Masters Страницы: 83

Бренд: Pfeiffer Vacuum Страницы: 24

Levalarm EA100 Series

Бренд: Clark-Reliance Страницы: 10

Z80-H536.08 S8RVW3

Бренд: Jäger Страницы: 48

7x7 NG Plus 4 Series

Бренд: Monosem Страницы: 94

Бренд: Danfoss Страницы: 56

Бренд: Ulvac Страницы: 29

Бренд: Ulvac Страницы: 55

HD67801-KNX-BIP-B2

Бренд: ADF Web Страницы: 31

Бренд: Orenco Страницы: 2

Бренд: King Young Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды