background image

B-14

Solid-state Multi-functional Timer 

H3DS-M/-S/-A

Characteristics

Note:

For reference:
A maximum current of 0.15 A can be switched at 125 VDC (cos

φ

=1).

A maximum current of 0.1 A can be switched if L/R is 7 ms.
In both cases, a life of 100,000 operations can be expected.
The minimum applicable load is 10 mA at 5 VDC (failure level: P).

Accuracy of operating time

±

1% max. of FS (

±

1% 

±

10 ms max. at 1.2-s range)

Setting error

±

10% 

±

50 ms max. of FS

Signal input time

50 ms min.

Influence of voltage

±

0.7% max. of FS (

±

0.7% 

±

10 ms max. at 1.2-s range)

Influence of temperature

±

5% max. of FS (

±

5%

±

10 ms max. at 1.2-s range)

Insulation resistance

100 M

 min. at 500 VDC

Dielectric strength

Between current-carrying metal parts and exposed non-current-carrying metal parts: 2,000 VAC for 1 min.
Between control output terminals and operating circuit: 2,000 VAC for 1 min.
Between contacts not located next to each other: 1,000 VAC for 1 min.

Vibration resistance

Malfunction: 0.5-mm single amplitude at 10 to 55 Hz
Destruction: 0.75-mm single amplitude at 10 to 55 Hz

Shock resistance

Malfunction: 100 m/s

2

 3 times each in 6 directions

Destruction: 1,000 m/s

2

 3 times each in 6 directions

Impulse withstand voltage

3 kV (between power terminals)
4.5 kV (between current-carrying metal parts and exposed non-current-carrying metal parts)

Noise immunity

Square-wave noise generated by noise simulator (pulse width: 100 ns/1 

µ

s, 1-ns rise) 

±

1.5 kV

Static immunity

Malfunction: 4 kV
Destruction: 8 kV

Life expectancy

Mechanical: 10 million operations min. (under no load at 1,800 operations/h)
Electrical:

100,000 operations min. (5 A at 250 VAC, resistive load at 360 operations/h)
(see note)

EMC

(EMI)

EN61812-1

Emission Enclosure:

EN55011 Group 1 class B

Emission AC Mains:

EN55011 Group 1 class B

Harmonic Current:

EN61000-3-2

Voltage Fluctuation and Flickering: EN61000-3-3
(EMS)

EN61812-1

Immunity ESD:

EN61000-4-2: 6 kV contact discharge (level 3)

8 kV air discharge (level 3)

Immunity RF-interference from AM Radio Waves: 

EN61000-4-3: 10 V/m (80 MHz to 1 GHz) (level 3)

Immunity Burst:

EN61000-4-4: 2 kV power port and output port (level 3)

1 kV control port with capacitive clamp (level 3)

Immunity Surge:

EN61000-4-5: 2 kV common mode (level 3)

1 kV differential mode (level 3)

Case color

Light gray (5Y7/1)

Degree of protection

IP30 (Terminal block: IP20)

Weight

Approx. 70 g

Содержание H3DS Series











































Отзывы: