background image

Solid-state Star-delta Timer

 

H3DS-G

B-35

Ti

m

e

rs

Operation

Basic Operation

Setting of Selector

The selectors can be turned clockwise and counterclockwise to
select the desired time scale, or operating mode.

Each selector has a snap mechanism that secures the selector at a
given position. Set the selector at a position at which it is secured. Do
not set it midway between two securing positions or a malfunction
could result from improper setting.

Selection of Time Unit and Time Scale

The star-delta transfer time and star operation time scale are set with
the same selector. The star-delta transfer time can be set to 0.05,
0.1, 0.5, or 1. The star operation time scale can be set to a multiplica-
tion factor of 1 or 10. If the star-delta transfer time is displayed in the
display window in white letters, this means that the star operation
time scale is “x10”. Refer to the example below.

Time Setting

The star operation time of the Timer is set with the time setting dial.

Locking/Unlocking of Selectors and 
Time Setting Dial

The time setting dial and time scale selector can be locked using the
Y92S-38 Lock Key, a special pen type tool that is sold separately. To
lock the dial or selectors, insert the Lock Key in the keyhole to the
lower right of the dial or selector and turn it clockwise until the dial or
selector is completely covered with the red cover. To unlock, turn the
Lock Key in the opposite direction.

Timing Charts

Note:

The reset time requires a maximum of 0.5 s.

Star-delta transfer time

Star operation time scale

x1

x10

0.05 s

0.1 s

0.5 s

1 s

0.05 s

0.1 s

0.5 s

1 s

Star-delta transfer time and 
star operation time scale 
display window and selector

Key hole

Power (A

1

 and A

2

)

Star contact 
17 and 18  
(star indicator)

Delta contact 
27 and 28 
(delta indicator)

t

1

: Star operation time setting

t

2

: Star-delta transfer time

ON
OFF

ON
OFF

ON
OFF

0.5 s

t

1

t

2

Содержание H3DS Series











































Отзывы: