Omron H3DS Series Скачать руководство пользователя страница 38

Страница: 38 / 42

B-46

Common to All Timers

H3DS-

@LC

■

Wiring

Use wires of the applicable sizes specified above. The length of the
exposed conductor should be 6 to 7 mm.

Use the following wiring procedure.

Insert the specified screwdriver into the release hole located
beside the wire connection hole where the wire is to be inserted.

Insert the exposed conductor into the wire connection hole.

Pull out the screwdriver.

■

Precautions

Always insert the screwdriver straight into the hole, never at an angle.
The clamp spring may be deformed if the screwdriver is not straight.

Do not move the screwdriver side to side in the clamp hole. The
clamp spring may be deformed if the screwdriver is moved sideways.

6 to 7 mm

Fig. 1 Exposed Conductor Length

Wire
connection
holes

Release
holes

Fig. 2 Wire Connection Holes and Release Holes

Wire connection hole

Fig. 3 Section A-A of Fig. 2

Release hole

Screwdriver

Insert

Pull out

Содержание H3DS Series











































Результаты поиска

Содержание H3DS Series

Отзывы:

Похожие инструкции для H3DS Series

Бренды по названию

Популярные бренды

Omron H3DS Series, Руководство пользователя

Результаты поиска

Содержание H3DS Series

Отзывы:

Похожие инструкции для H3DS Series

Бренды по названию

Популярные бренды