Omron E5 K-T - Скачать руководство пользователя страница 7

Страница: 7 / 44

E5AK-T/E5EK-T

Output Unit Ratings and Characteristics

Model

Specifications

E53-R

Relay output

5 A at 250 VAC (resistive load)

E53-S

SSR output

1 A at 75 to 250 VAC (resistive load)

E53-Q

Voltage output

NPN: 40 mA at 12 VDC

(with short-circuit protection)

E53-Q3

NPN: 20 mA at 24 VDC

(with short-circuit protection)

E53-Q4

PNP: 20 mA at 24 VDC

(with short-circuit protection)

E53-C3

Linear current output

4 to 20 mA, permissible load impedance: 600

Ω

max., resolution: approx. 2,600

E53-C3D

0 to 20 mA, permissible load impedance: 600

Ω

max., resolution: approx. 2,600

E53-V34

Linear voltage output

0 to 10 VDC, permissible load impedance: 1 k

Ω

min., resolution: approx. 2,600

E53-V35

0 to 5 VDC, permissible load impedance: 1 k

Ω

min., resolution: approx. 2,600

Note:

An output relay (1 A at 250 VAC) is mounted on the position-proportional model. (When replacing, use the E53-R.)

Option Unit Ratings and Characteristics

Model

Specifications

E53-AKB

Event input

Contact input:
ON: 1 k

Ω

max., OFF: 100 k

Ω

min.

No-contact input:
ON: residual voltage 1.5 V max., OFF: leakage current 0.1 mA max.

E53-AK01

Communications

RS-232C

Transmission method:

Half-duplex

th d

St t t

(

th d)

E53-AK02

u ca o s

RS-422

a s

ss o

e od

a du e

Synchronization method: Start-stop synchronization (asynchronous method)
Baud rate:

1 2/2 4/4 8/9 6/19 2 kbps

E53-AK03

RS-485

Baud rate:

1.2/2.4/4.8/9.6/19.2 kbps

E53-AKF

Transfer output

4 to 20 mA:
Permissible load impedance: 600

Ω

max.

Resolution: approx. 2,600

Note:

Event input is used for switching the target value, run or stop command, or automatic and manual mode with an external signal input.

Current Transformer Ratings

Dielectric strength

1,000 VAC (for 1 min)

Vibration resistance

50 Hz, 98 m/s

(10G)

Weight

E54-CT1: approx. 11.5 g; E54-CT3: approx. 50 g

Accessories (E54-CT3 only)

Armature: 2; Plug: 2

Heater Burnout Alarm

Max. heater current

Single-phase 50 A VAC (see note 1)

Heater current value display accuracy

5% FS

1 digit max.

Heater burnout alarm setting range

0.1 to 49.9 A (in units of 0.1 A) (see note 2)

Min. detection ON time

190 ms (see note 3)

Note:

1. Use the K2CU-F

A-

GS (with gate input terminals) for the detection of three-phase heater burnout.

2. The heater burnout alarm is always OFF if the alarm is set to 0.0 A and always ON if the alarm is set to 50.0 A.

3. No heater burnout detection or heater current value measurement is possible if the control output (heat) is ON for less than 190 ms.

Содержание E5 K-T -













































Результаты поиска

Содержание E5 K-T -

Отзывы:

Omron E5 K-T -, Руководство пользователя, Страница: 7 / 44

Результаты поиска

Содержание E5 K-T -

Отзывы: