manualshive.com logo in svg

Omron E5 K-T -, Руководство пользователя, Страница: 37 / 44

Поделиться
Скачать
Omron E5 K-T - Скачать руководство пользователя страница 37

E5

j

K-T

E5

j

K-T

37

Expansion Mode

Set Point Upper
Limit

Set Point
Lower Limit

PID/ON/OFF
(not displayed for control valve control)

α

Available if the Controller is in 2-PID
control.

AT Calculated Gain
Available if the Controller is in 2-PID
control.

AT Hysteresis
Available if the Controller is in 2-PID
control.

LBA Detection Width
Available only when the LBA (loop break
alarm) function is assigned.
Unavailable to the E5

j

K-PRR2.

Operation at Power ON

End condition

Automatic Return of Display Mode

Number of Patterns (Displayed for E5CK.)

Program Time Unit

Stop Time/Rate of Rise Programming

Time Unit of Ramp Rate (used for Rate of Rise Setting)

PV Start (used for setting time)

Wait Width (available for E5AK or E5EK.)

Alarm During Ramp Step Enable

Run All Enable (with E5CK, this display appears
when more than two patterns are used.)

Option Mode

Event Input Assignment 1
Available for the event input function.

Event Input Assignment 2
Available for the event input function.

Event Input Assignment 3
Available for the event input function.

Event Input Assignment 4
Available for the event input function.

Communication Stop Bit
Used when the communications function is being used.

Communication Data Length
Used when the communications function is being used.

Communication Parity
Set when the communications function is being used.

Communication Baud Rate
Set when the communications function is being used.

Communication Unit No.
Set when the communications function is being used.

Transfer Output Type
Set when the transfer output function is being used.

Transfer Output Upper Limit
Set when the transfer output function is being used.

Transfer Output Lower Limit
Set when the transfer output function is being used.

For E5

j

K-PRR2

Motor
calibration

Travel time

PV dead
band

HBA latch

Содержание E5 K-T -













































Отзывы:

Нет отзывов