Omron E5 K-T - Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 44

Omron E5 K-T - Скачать руководство пользователя страница 16

E5

j

K-T

E5

j

K-T

16

2. Insert the Option Unit into the socket for option 1. The

following diagram shows the relationship between Option
Unit and mounting position.

Option 1
E53-AKB: Event inputs 1/2
E53-AK01: RS-232C
E53-AK02: RS-422
E53-AK03: RS-485
E53-AKF: Transfer output

3. Mount the Option Board and the power board in the order

shown.

Mounting

1. Insert the E5EK-T Controller into the mounting hole in the

panel.

2. Fit the mounting bracket (accessory) into the fixing slots on

the top and bottom of the rear case.

3. Tighten the mounting bracket screws alternately a little at a

time until the ratchet starts to slide.

Setting Up the Terminal Cover

Fasten the Terminal Covers (E53-COV0809) to protect terminals.

E5AK-VV2-500 Controller is provided with Terminal Covers.

Use E53-COV09 for terminals 1 to 10, and E53-COV08 for termi-
nals 11 to 33.

Fasten the Terminal Covers as follows by using the snap pins.

E5AK-T

E53-COV08

To remove the Terminal Covers, pull the edges of the snap pins.

«
...
14
15
16
17
18
...
»

Содержание E5 K-T -













































Отзывы:

Нет отзывов